background image

Thank you very much for choosing this product! For future reference, please complete the owner

record below:

Model: ___ATV-CBP__     Purchase Date: _______________

Save the receipt, warranty and these instructions. It is important that you read the entire manual to 
become familiar with this product before you begin using it. 
This machine is designed for certain applications only. The manufacturer cannot be responsible for 
issues arising from modification. We strongly recommend this machine not be modified and/or used 
for any application other than that for which it was designed. If you have any questions relative to a 
particular application, DO NOT use the machine until you have first contacted us to determine if it 
can or should be performed on the product.

For technical questions please call 

1-218-943-6296

.

INTENDED USE

Planter is designed for planting small feed plots or hobby farm.

TECHNICAL SPECIFICATIONS

Manual lift for raising and lowering
13" Pneumatic tires
Adjustable row width from 14"-36"
Ground Driven
Measurements of hopper: 12"x6" at top, 10"x2" at bottom, 8" deep
.22 bushels/hopper, 32 cups/hopper, 1.75 gallons

WARNING:

Read and understand all instructions.

Failure to follow all instructions listed below 

may result in serious injury.

CAUTION:

Do not allow persons to operate or assemble this planter until they have read 

this manual and have developed a thorough understanding of how the planter works.

WARNING:

The warnings, cautions, and instructions discussed in this instruction manual 

cannot cover all possible conditions or situations that could occur. 

It must be understood by the 

operator that common sense and caution are factors which cannot be built into this product, but must 

be supplied by the operator.

2

pp

y

p

SAVE THESE INSTRUCTIONS

Содержание ATV-CBP






















Отзывы: