background image

Page      of 15 

 

Thank  you  very  much  for  choosing  this  product!  For  future  reference,  please  complete  the 

owner’s record below: 

            Model:                                      Purchase Date: _______________ 

Save the receipt, warranty and these instructions. It is important that you read the entire manual 

to become familiar with this product before you begin using it.   

 
This product is designed for certain applications only. The manufacturer cannot be responsible 
for issues arising from modification. We strongly recommend this product not be modified and/or 
used  for  any  application  other  than  that  for  which  it  was  designed.  If  you  have  any  questions 
relative to a particular application, DO NOT use the product until you have first contacted us to 
determine if it can or should be performed on the product. 

 

INTENDED USE 

This ATV seeder has 8 rows to seed corn, beans, oats, etc.    There are two boxes with closeable 

slides for each row.    The seeder has adjustable slots to use for different types of seed. This 

seeder is also able to seed grain. 

TECHNICAL SPECIFICATIONS   

Weight 

529 lbs 

Rated Horse Power 

Minimum 20 HP 

Seeding Rows 

Row Spacing 

5.3 inches 

Seed Rate 

Each hole up to 20 lbs per acre 

 

GENERAL SAFETY RULES 

WARNING:

 Read and understand all instructions.

 Failure to follow all instructions listed 

below may result in serious injury. 

 

CAUTION:

 Do not allow persons to operate or assemble this  seeder

 

until they have 

read this manual and have developed a thorough understanding of how the seeder

 

works.

 

 

WARNING:

  The  warnings,  cautions,  and  instructions  discussed  in  this  instruction 

manual  cannot  cover  all  possible  conditions  or  situations  that  could  occur. 

It  must  be 

understood by the operator that common sense and caution are factors which cannot be built into 

this product, but must be supplied by the operator. 

 

 

 

 

 

Содержание ATV-48ATVPS
















Отзывы: