Fidelity Electronics 19eA Скачать руководство пользователя

Страница: 45 / 62

18. Error Codes

Error Code No.

Description

Err 1

Time value error

Err 2

Date value error

Err 3

Exceed manual zero

Err 4

Offset out of range / unstable during power on (5 minutes for OIML and NTEP mode)

Err 5

No load cell detected

Err 6

Tare operation error

Err 7

Logic error. HI limit set is lower than LO limit (and HI is not = 0)

Err 8

Logic error. LO limit is higher than HI limit (and HI is not = 0)

Err 10

(F25 Mode 3) Container weight is higher than tArE H

Err 11

(F25 Mode 3) Container weight is lower than tArE L

Err 12

(F25 Mode 3 and Mode 4) Actual weight is higher than SP3

Err 13

Exceed maximum power on (5 minutes for OIML and NTEP mode)

Err 19

Capacity or division setting error (Division set is higher than 10000d)

Err 22

Manual Zero and Tare stability error

Err 23

Capacity setting error, Capacity 1 > Capacity 2

Err 24

Division setting error, e1 > e2

Err 25

Span gain is too low

Err 26

Not able to obtain stable status for longer than 10 sec

Err 27



Theoretical calculated value per e of Cal 2 varies more than 1% as of Cal 1.
Properly a load cell problem.



Mass value of Cal 2 is less than 150% of Cal 1.

Err 28

Maximum accumulation limit is exceeded.

Err 29

Standard deviation data exceed memory size (300 transactions).

--oL--

Overload (Gross weight is more than Max plus 9d)

HALT

Major system error detected. Power off instrument and remove power adaptor
immediately. Then check load cell connection and system power status.

UndEr

Negative Weight values exceeds display range

Reboot

Important parameters have been changed. Power off and then power on instrument
again to reboot.

------

Negative Tare value exceeds display range

19. Daily Care & Maintenance

Clean the instrument with a soft, damp cloth. If necessary, use a mild detergent in water.

Do not use any harsh, abrasive material, acetone, volatile solvent, thinner or alcohol for cleaning.

Verify the accuracy of this instrument periodically. Re-calibrate if necessary. In some countries, calibration
requires authorized/qualified agent. Contact your dealer for more information.

Store this instrument in a dry and clean place,

Recharge battery before and every 4 months during long time storage.

Содержание 19eA































































Результаты поиска

Содержание 19eA

Отзывы:

Похожие инструкции для 19eA

Бренды по названию

Популярные бренды

Fidelity Electronics 19eA, Руководство по эксплуатации

Результаты поиска

Содержание 19eA

Отзывы:

Похожие инструкции для 19eA

Бренды по названию

Популярные бренды