Fibocom L860-GL страница 31 Скачать руководство пользователя

Страница: 31 / 254

FIBOCOM L860 AT Commands User Manual

Page 31 of 254

3.1.17 +CLAC, List of All Available AT Commands

This command prints out all AT Commands supported by the Modem.

Command

Description

Execution

[Function]

The Execution command displays a list of all the AT commands supported by the

Modem.

[Syntax]

AT+CLAC

[Response/Action]

List of available AT commands

Read

N/A

Test

N/A

Parameters

N/A

Example

AT+CLAC

ATS

ATD

ATA

ATO
...
...

Reference

3GPP TS 27.007

4 Modem Control and Status

4.1 Modem Register Commands

The modem holds certain data items in selected memory space, named Software Registers (S-registers)

and Modem Registers. Some of these registers are used as bitmaps, where one register holds more than

one data item. All S-registers can be accessed using the S command, described in “S, Bit Map Registers”.

Some registers can also be accessed using dedicated commands, detailed below.

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды