Fibocom L860-GL Скачать руководство пользователя

Страница: 187 / 254

FIBOCOM L860 AT Commands User Manual

Page 187 of 254

Command

Description

AT+CLK26M=?

[Response/Action]

+CLK26M: (list of supported <n>s)

Parameters

<n>

0: switch off the clock, default value.

1: switch on the clock

Example

11 GPRS

11.1 GPRS Functionality

GSM 07.07 defines commands that a TE may use to control a GPRS ME via a non-multiplexed

character-stream interface. This places certain limitations on the functionality of the interface. For

example, it is not possible for the ME to send control information to the TE or for the TE to send

commands to the ME whilst the interface is in the online data state, unless the layer 2 protocol itself

supports this feature (GSM 07.60-12). However, Modem-specific escape mechanism (DTR) is provided to

enable the TE to switch the Modem into limited online command state.

The use of a multiplexed interface, (GSM 07.10), is not considered here (See “Multiplexer Feature”). The

Modem-specific escape mechanism use DTR as an escape signal (following &D parameters) and

designed for limited non network related commands. This specific mechanism purpose is to give the user

a way to retrieve the signal strength. The time limit of consecutive DTR toggles is a minimum of 90

seconds. The Modem-specific is not designed to support online command and data states both at the

same time, therefore any wrong or extreme usage can cause unexpected behaviors. The basic GPRS

concept is be “always connected” and there is no charge for being connected (only per real data

transferred).

11.2 GPRS Commands

This section defines commands that a terminal may use to control a GPRS ME. GPRS MTs vary widely in

functionality. A class A ME might support multiple PDP-types as well as circuit-switched data, and use

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды