FiberHome AN6000-15 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 24

FiberHome AN6000-15 Скачать руководство пользователя страница 18

17

12

Connecting Network Cables

Subrack Side (RJ-45)

Opposite Side (RJ-45 / Bare Wire)

SFP+ ports 1 to 4 of the HSCA card

Connected to an IP network for uplinking.

Ports 1 to 8 of the HU8A card

ETH interface of the HSCA card

Connected to an out-of-band network management computer
to implement network management monitoring.

EMS interface of the CIOA card

ESC interface of the HSCA card

Connected to an environment monitoring device to report the
external environment status to the network management
system.

ALM interface of the CIOA card

Connected to one of the terminals XS1 to XS4 on the
PDP850A (3000064) to output the subrack alarms to the PDP.

1PPS/TOD interface of the CIOA card

Connected to an external clock device.

Note 1

DC1-7 interface of the CIOA card

Connected to a dry contact device.

Note 1

Note 1: The cable is connected by bare wires on this side.

Connection

Network cable

Connected to the Opposite End Equipment

Instruction

3

1

2

Route the network cables behind the left
vertical mounting flange, in the space
between the subrack side panel and the
cabinet side panel. Lead them to the bottom
of the subrack, thread them through the
wiring holes of the fiber passage unit, and
then connect them to the desired cards.

«
...
16
17
18
19
20
...
»

Содержание AN6000-15

























Отзывы:

Нет отзывов