background image

Manual for motor FM 170 B2 - FS ( Date of publication 06/2016)

 

 

FIALA PROP s.r.o,  Vysoká 56,  75641 LEŠNÁ ,  Czech Republic , e-mail: [email protected] 
www.fialaprop.com

 

 

Page 5 

 

If a situation arises that the engine will not start, there was either a glut motor fuel, or vice versa 
engine is lean. 

Because these conditions can be difficult to detect, we recommend the following procedure: 

- Check the fuel system (leaks, throughput, level of fuel etc.). 

- Make sure that the ignition is switched off 

- Set full throttle 

- 10 x spin the motor 

- Turn the ignition 

- Set a slightly increased idle speed of about 3-8% (must be tested on a specific motor) 

- Start the motor 

If the engine can no longer run, we recommend: 

- Make sure that the ignition is switched off 

- Close the choke 

- 3-4 times to spin the motor, in order to draw fuel 

- Open the choke and set the throttle 

- 1 x spin the motor 

- Set a slightly increased idle speed of about 3-8% (must be tested on a specific motor) 

- Turn the ignition 

- Start the motor 

If the engine still does not start, it is necessary to contact an authorized service center or the 
manufacturer directly. 
 

7.

 

 Running motor 

Each motor is factory-tested and adjusted to the basic setting. Use a fuel with a higher ratio of oil 
(see section 3 of this manual), ie. 1:25. While running is not recommended long term exceed the 
motor speed 2500 / min while controlling the temperature of the engine. Do not keep a constant 
speed but motor flush with the occasional addition / slow down the gas. This mode observe about 
the first 30 minutes of operation. After a short time, you can gradually increase the speed up to 4000 
/ min. Total time of run is about 2 hours. 

 

Содержание FM 170 B2-FS









Отзывы: