Festool PRECISIO CS 70 EBG, Оригинальное руководство пользователя

Страница: 31 / 193

31
Make sure that all rotary knobs on the
preset profile setting rail are tightened
before starting work. The preset profile
setting rail should always be used in a
fixed position and must not be used to
push the workpiece.
When not in use, fold the preset profile
setting rail
[11-3]
to the zero position
(fig. 15) and put it in the accessory holder
[11-4]
[fig. 11].
8.11 Fitting the splinter guard [10-3]
WARNING
Risk of accident, electric shock
f
Always disconnect the mains plug from the
socket before performing any work on the
machine.
NOTE
The splinter guard cannot be used when making
bevel cuts. Remove the splinter guard as neces-
sary.
f
Unscrew the rotary knob [5-1] .
f
Slide the clamping plate forwards.
f
Lift the table insert
[1-7]
at the rear and
remove it.
f
Set the saw blade to the minimum cutting
height.
f
Fold the small cover
[10-1]
down.
f
Push the splinter guard [10-3] sideways all
the way into the holder
[10-4]
.
f
Place the table insert
[1-7]
in position and
tighten the rotary knob [5-1] .
f
Switch on the machine and move the saw
blade slowly upwards to the maximum cutting
height.
This cuts into the splinter guard. The raised sec-
tion
[10-2]
of the splinter guard should protrude
slightly (by approx. 0.3 mm) over the edge of the
table so that it functions more effectively.
f
To adjust the height of the holder
[10-4]
,
unscrew both screws
[10-5]
.
8.12 Dust extraction
WARNING
Breathing in dust can damage the respiratory
tract.
f
Always connect the machine to a dust extractor.
f
Always wear a dust mask when performing
work that generates dust.
The PRECISIO has two vacuum connections: Top
vacuum connection with bayonet coupling (4-7)
with a diameter of 27 mm and lower vacuum con-
nection (4-3) with a diameter of 35 mm. To guide
the top suction hose, attach the hose holder
[4-6]
to the clamping rail on the saw table.
The CS 70 AB extractor set
[4-4] (included with
the CS 70 EBG) joins both suction connections
to enable a Festool mobile dust extractor with a
50 mm adapter to be connected.
8.13 Scale
Use retaining screws to set the scale to different
saw blade widths as necessary.
8.14 Adjusting the guard
To adjust the stops, the guard can be locked in
place in the upper position.
f
Lock the lateral splinter guard
[8-3]
with the
catch in the upper position [8-2] .
f
Lift the guard into the upper position
[8-4]
and
tighten the screw [8-1] .
f
After adjusting the stops, loosen the screw
[8-1]
again and remove the lateral splinter
guard [8-3] . NOTE : The guard and the splinter
guard must lie freely on the plate (fig. 9).
f
When not in use, the guard should be attached
to the accessory holder [11-4] .
9 Working with the machine
WARNING
Risk of injury
f
Always read all safety instructions when
working with the machine.
f
Make sure that all rotary knobs on the fence
and the machine are tightened before starting
work.
f
Do not work with oversized and heavy work-
pieces that could damage the tool.
f
For safety reasons, NEVER work without an
upper guard [1-8] fitted (except for concealed
cuts).
f
Perform measurement settings when the
machine is at a stillstand.
Set the top guard so that it is in contact with the
workpiece.
9.1 Using the machine as a table saw
When bench sawing, the saw remains fixed in
place and the workpiece is moved.
P R E C I S I O
-
GB