Festool LEX 2 125/3, Руководство по эксплуатации

Страница: 4 / 6

6
Technical data
Sanding pad diameter
- LEX 2 125 125 mm
- LEX 2 150 150 mm
- LEX 2 185 185 mm
Drive Compressed-air vane motor
Operating pressure (flow pressure) 6 bar
Speed 4,000 - 8,000 rpm
Working strokes 8,000 - 16,000 rpm
Sanding stroke
- LEX 2 125/3, LEX 2 150/3 3 mm
- LEX 2 125/7, LEX 2 150/7,
LEX 2 185/7 7 mm
Air consumption at nominal load 390 l/min
Weight
- LEX 2 125, LEX 2 150 1.3 kg
- LEX 2 185 1.4 kg
The specified illustrations can be found at the
beginning of the operating instructions.
1 Use for intended purpose
As specified, the machines are designed for
sanding wood, plastic, metal, stone, composite,
paintwork, filler and similar materials.
Material containing asbestos must not be
processed with these tools.
The user is liable for damage and injury
resulting from incorrect usage!
2 Before starting up, please observe
the following
2.1 Safety
Before using the machine, please read
the enclosed safety instructions.
- The manufacturer’s handling and processing
instructions must be observed without fail if
explosive or self-igniting dusts are likely to
occur during sanding.
- If dust dangerous to health is produced during
sanding, the machine should be connected
to an appropriate extraction device and the
safety regulations that apply to the working
material should be observed.
- The operating pressure should not exceed 6.5
bar.
- The machine should only be operated with
sandpaper. Grinding wheels and parting
grinder discs are not permitted.
- Only work with correctly processed
compressed air. Using the Festool service unit
VE guarantees this.
- Only use original Festool accessories.
- Wear suitable protection such
as ear protection, safety
goggles, a dust mask for work
which generates dust, and
protective gloves when
working with raw materials
and when changing tools.
2.2 Noise and vibration information
Typical values established in compliance with
EN ISO 15 744 / EN ISO 8662:
Sound pressure level 70 dB(A)
Measured acceleration
- LEX 2 125, LEX 2 150 2.7 m/s
2
- LEX 2 185: 5.0 m/s
2
The noise level can exceed 85 dB(A)
during work. Wear ear protectors!
3 Compressed-air supply and
commissioning
Make sure that the pneumatic tool is
switched off when you connect the
compressed-air supply.
3.1 Compressed-air processing
The Festool service unit should always be used
to ensure that Festool pneumatic tools function
correctly.
Consisting of a filter, control unit, condensation
drain and lubricator, the service unit cleans and
lubricates the compressed air and keeps it free
of condensation.
Here, the lubricator should be set so that a
drop is applied to the compressed air approx.
every 7-10 minutes.
Damage that occurs as a result of incorrect
compressed-air processing is excluded from
warranty claims.
We recommend a service unit with a 3/8"
connector, when up to two Festool pneumatic
tools are used.
A compressor that supplies at 500 l/min and
at an operating pressure of 6 bar should be
used to supply compressed-air.
The diameter of the piping system must be
sufficiently large (at least 9 mm).
3.2 IAS 2 hose connector
The eccentric sander is a pneumatic tool for
connection to the Festool IAS 2 system.
This hose system combines three functions in
one hose:
- Compressed air supply (1.1)
- Exhaust air extraction (1.2)
- Dust extraction (1.3)
Connection and disconnection – see Fig. 3.
IAS 2 connecting system – see accompanying
instruction sheet.
3.3 Commissioning
Pressing the lever (2.1) switches on the
pneumatic tool.
Releasing the lever switches the machine off
again.
4 Machine settings
The machine should always be dis-
connected from the compressed air
supply before any work is carried out
on the machine.
Seen at Ideal Tools.