D U R A D R I V E
17
GB
Attach the depth stopper on the bit (see figure
[4b]
.
By means of jamming the depth stopper with
the bit and concurrent pulling, it is possible to
pull out the bit.
Then attach a new bit in the holder.
9
Working with the machine
9.1
On/Off switch [1-2]
Pressing only the switch
[1-2]
does not start the
machine –
it is not a machine fault
!
Upon screwing to the required depth, the power
tool switches off!
The machine can be switched on by means of sev-
eral methods:
a)
Set the forward / reverse switch
[1-3]
into ma-
chine clockwise operation.
Set the switch
[1-4]
into MAN position.
In order to switch on the power tool, apply the
switch
[1-2]
and concurrently press the bit on
the screw.
Use the switch
[1-2]
to gradually regulate the
speed.
b)
Set the forward / reverse switch
[1-3]
into ma-
chine clockwise operation.
Set the switch
[1-4]
into AUTO position.
Press the bit on the screw and the power tool
will switch on.
Switch
[1-2]
does not need to be pressed. Maxi-
mum speed is set automatically.
b)
Set the forward / reverse switch
[1-3]
into ma-
chine anti-clockwise operation.
In order to start the power tool, press the switch
[1-2]
.
The switch MAN/AUTO
[1-4]
is in any position.
Use the switch
[1-2]
to gradually regulate the
speed.
If the forward / reverse switch is set to anti-
clockwise operation, the screwdriver can be
started only by pressing the switch
[1-2]
without
additional pressure on the bit.
It is not necessary to remove the depth stopper
in order to unscrew screws.
9.2
Depth stop
Turning the depth stopper
[1-5]
sets the screwing
depth – see figure
[5]
. The setting accuracy is ap-
prox ± 0,1 mm.
Upon setting the depth, set some screws to test and
adjust the depth.
Depth stop assembly
Fit the depth stop
[4-1]
on the gear box
[4-5]
.
Press until it engages in the groove.
Depth stop disassembly
Remove the depth stop from the gear box by
pulling it.
9.3
Scaffolding holder and belt clip
Use the belt clip
[6-1]
to temporarily attach the
screwdriver on the working clothing – it can be at-
tached by means of a screw
[6-2]
to the left or right
of the power tool, and it is suitable for right and left
handed people – see figure
[6]
.
The screwdriver is equipped with a scaffolding
holder
[7-1]
which is used for occasional machine
suspension. It can be attached to the left or right of
the power tool, by means of a screw
[7-2]
– see fig-
ure
[7]
.
9.4
Magazine attachment
The magazine attachment enables to work contin-
uously, without unnecessary delays.
Fitting the magazine attachment
At first remove the depth stopper
[4-1]
and bit,
bit holder
[4-2]
as specified in chapter 8.
Set the switch
[1-4]
into MAN position.
Push the long bit
[8-1]
completely to the hexag-
onal spindle opening
[4-4]
.
Then fit the magazine attachment on the gear
box. Push the attachment until it engages in the
groove of the gear box.
The attachment can be mounted at 30° steps.
Removing the magazine attachment
Use power to carefully pull the magazine at-
tachment from the gear box.
Setting the screw length
Press button
[9-1]
to remove and insert the
depth stop
[9-2]
and set the required screw
length.
Anti-clockwise
rotation
screws are inserted deeper
Clockwise rotation screws are inserted to lower
depth
