Festool CMS-MOD-BS 120, Оригинальное руководство по эксплуатации

Страница: 12 / 65

12
CMS-MOD-BS 120
GB
7.3 Height adjustment
A sanding belt usually wears most in the area di-
rectly above the table top. To ensure that the sand-
ing belt wears evenly across its whole width one
side of the sanding unit can be lowered. Release the
rotary knob (2.4) and lower accordingly with the grip
(2.4) of the swivel arm on the side of the table oppo-
site the switch. Retighten the swivel arm after ad-
justment. The stop screw (2.5) can be set accord-
ingly to ensure that the sanding rotter is exactly
vertical to the tabletop when swivelled back into its
normal position.
8 Working with the machine
8.1 Face sanding
The useful sanding area for face sanding is the part
of the belt between the two markings on the upper
roller guard (1.6).
8.2 Sanding rounded parts
Free access to the pivoted sanding roller enables
rounded parts to be sanded. Sanding rollers with
various diameters can be fitted to sand various
shaped rounded parts (1.5).
8.3 Dust extraction
There are two connections for a dust extractor to
enable dust-free working with the belt sander. The
collector (2.1) should hereby be placed close to the
area of work, approx. 2 mm away from the sanding
belt and fastened to the tabletop. The dust extractor
should be connected to the collector's lower suc-
tion adapter. The upper suction adapter is connect-
ed to the drive roller guard's suction adapter (2.6)
with a short piece of hose. When working with wood
or using materials which produce harmful dusts
the electric tool must be connected to a suitable
dust extractor.
Attention: Do not collect metal dust in a dust ex-
tractor which already contains inflammable dusts
(fire risk).
8.4 Guide
As shown in Fig. 4, the supplied guide can be se-
cured to all four sides of the machine.
The guide offers the following adjustment options:
– Adjustment parallel to the bench edge - open the
rotary knob (4.7).
– Adjustment vertical to the bench edge - open the
rotary knob (4.6).
– Adjustment of the sliding fence (4.1) in a longitu-
dinal direction - open the rotary knob (4.4). The
sliding fence can be clamped onto the holder in a
low position for thin workpieces (Fig. 5), or in a
high position for thick workpieces (Fig. 4).
– Angle adjustment using the scale (4.5) - open the
rotary knob (4.3) and raise the fixing pin (4.2). The
rotating fixing pin locks into place in the most
common angle positions. (Note: turning the lo-
cating pin blocks the stop)
Prior to all work, make sure that all rotary
knobs of the guide are tightened. The guide
may only be used in a fixed position and not
to shift the workpiece.
9 Service and maintenance
Customer service and repair only
through manufacturer or service
workshops: Please find the nearest
address at:
www.festool.com/Service
Use only original Festool spare parts!
Order No. at:
www.festool.com/Service
To ensure constant air circulation, always keep the
cooling air openings in the motor housing clean and
free of blockages.
9.1 Changing the sanding roller
The CMS-MOD-BS 120 is fitted with standard sand-
ing rollers with a diameter of 73.5 mm.
When changing the roller the upper roller guard
(1.8), the sheet metal washer in the tabletop match-
ing the roller diameter (1.4) and the ceramic start-
ing plate (1.12) must also be replaced. Release the
locking screw (1.10) with a 6 mm hexagon key to re-
place the roller.
Attention! Do not remove the wavy spring washer
between the shaft collar and roller. Fit other roller
and tighten in place. Insert sanding belt and tension
by releasing the lever catch. Then fit the sheet met-
al washer which matches the roller diameter so
WARNING
Risk of injury, electric shock

Always disconnect the mains plug from the
socket before performing maintenance work on
the machine!

All maintenance and repair work which requires
the motor housing to be opened must only be
carried out by an authorised service workshop.
EKAT
1
2
3
5
4