Festo MSE6-C2M Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 104

background image

60

Festo — MSE6-C2M — 2022-08b

Commissioning

8.5.2

Using the memory card

The memory card is used as a carrier of configuration data for PROFINET addressing and thus simpli-
fies bus node replacement:

–

PROFINET I/O device name

–

IP address

NOTICE

Malfunction or Damage to the Memory Card.
Inserting or removing the memory card while the power supply is switched on can result in malfunc-
tions of or damage to the memory card.
• Disconnect the power supply before you insert or remove the memory card.

Data stored on the memory card has priority over other configuration data which is stored, e.g. in the
bus node memory or in the higher-order controller.

1. Switch off the power supply.
2. Unscrew the retaining screws of the cover.
3. Remove the cover.
4. Insert the memory card.
5. Fit the cover.
6. Tighten the retaining screws of the cover. Tightening torque: 0.4 Nm ± 10%.

8.5.3

Connecting to the network

The bus node is connected to the network by a specific connection technology.

Bus node

Connection technology

Network connectors

CPX(-M)-FB43

2 sockets, M12, D-coded, 4-pin,
according to IEC 61076-2

NECU-M-S-D12G4-C2-ET plug

CPX(-M)-FB44

2x RJ45 bushing, push-pull,
AIDA-compliant, corresponding to
IEC 60603, IEC 61076-3

FBS-RJ45-PP-GS plug

Tab. 41: Connection technology and network connectors

The NECU-M-S-D12G4-C2-ET plug is designed for Ethernet cables with a diameter of 6 … 8 mm.
The FBS-RJ45-PP-GS plug is designed for Ethernet cables with a diameter of 5 … 8 mm.

Network connections on the bus node CPX(-M)-FB43
The network ports are labelled TP1 and TP2.

«
...
58
59
60
61
62
...
»

Содержание MSE6-C2M









































































































Отзывы:

Нет отзывов

Похожие инструкции для MSE6-C2M

Бренд: Camozzi Страницы: 33

Бренд: Camozzi Страницы: 2

Бренд: Camozzi Страницы: 64

Бренд: Danfoss Страницы: 24

Бренд: Eaton Страницы: 2

Бренд: Lamtec Страницы: 22

Бренд: National Instruments Страницы: 31

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 98

CompactRIO cRIO-9002

Бренд: National Instruments Страницы: 21

Бренд: National Instruments Страницы: 145

Бренд: National Instruments Страницы: 42

Бренд: National Instruments Страницы: 8

Бренд: National Instruments Страницы: 54

Бренд: S&P Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды