Festo EMCS-ST Скачать руководство пользователя

Страница: 76 / 86

Index.
Subindex

Name

Description

Data type
(length)

User access

U = User
M = Maintenance
personnel
S = Specialist

–

Control command for switch-
ing on the power stage. The
current position Pos

Act

of the

drive is maintained position-
controlled.

0x0002.0
(2.0)

SystemCom-
mand

Value 0xCD (205): Restore fact-
ory settings
–

Control command to reset
the drive unit to factory set-
tings

11.2.2 Factory settings.

–

After reset to the factory set-
tings, the drive must be ref-
erenced

11.3.2 Homing.

UIntegerT
(1 byte)

–

1) R/W = read and write, R = read only, W = write only

Tab. 38 System parameters

14.2.5

Control end-to-end operation via IO-Link

The following table shows the combinations of the process parameters "Mov

" and "Mov

Out

" or the

system parameter "System Commands" via IO-Link for controlling the drive in end-to-end operation.

Process parameters

System parameters

Description

"Mov

Out

System commands

0x0029.1

0x0029x2

0x0002

false

Stop motion
0xCA
(202)

Control command for stopping travel.
–

The power stage remains active.

–

The drive decelerates to standstill.

–

The drive remains at position-controlled
standstill.

false

true

Mov

Out

0xC9
(201)

Control command for executing the motion
"Mov

Out

–

The drive moves position-controlled
towards the "Lim

Out

" end position.

IO-Link

Festo — EMCS-ST — 2020-04a

Содержание EMCS-ST






















































































Результаты поиска

Содержание EMCS-ST

Отзывы:

Похожие инструкции для EMCS-ST

Бренды по названию

Популярные бренды

Festo EMCS-ST, Руководство по эксплуатации

Результаты поиска

Содержание EMCS-ST

Отзывы:

Похожие инструкции для EMCS-ST

Бренды по названию

Популярные бренды