Mounting instructions (Original: de)
8037330
1407a
†‡
Adjusting kit
EADC-E12
Festo AG & Co. KG
Postfach
73726 Esslingen
Germany
+49 711 347-0
www.festo.com
1.
Parts list
19344d_1
1
Slot
nut
2
Adjusting
plate
3
M6x30
screw
4
Square
nut
5
Adjusting
bolt
6
Washer
7
Screw
M8x40
1)
(2x)
(1x)
(2x)
(2x)
(2x)
(2x)
(2x)
19344d_2
Not included in delivery:
8
Planar surface gantry
EXCH
(1x)
2.
Intended use
Adjusting kit EADC-E12:
Attachment and alignment of the planar surface gantry EXCH. Compensation
of a difference in height of up to 5 mm.
3.
Safety instructions and notes on mounting
Caution
Unexpected movement of components.
Injury due to electric shock, impact, squeezing.
Switch off power supply before mounting work.
Observe safety instructions (
applicable documents).
Note
Malfunction and material damage due to incorrect mounting.
If the mounting surface is not made of steel:
Select a different screw
7
suitable for the installation situation.
Thread depth
≥
14 mm intended on the mounting surface for the
screws
7
.
Mount properly (
section 4).
Observe tightening torques.
Information
Applicable documents
Description of the planar surface gantry: EXCH (mechanical installation)
–
Observe minimum number and distances of the adjusting kits.
–
Align planar surface gantry.
Accessories
www.festo.com/catalogue
: EXCH
4.
Mounting
19344d_3
Place slot nuts
1
in the pro-
file slot (A).
Clamp the adjusting
plate
2
to the slot nuts
1
using the screws
3
.
Position the adjusting
plate
2
. Observe minimum
number and distances of the
adjusting kits (
Info
).
Tighten screws
3
.
19344d_8
Screw adjusting bolts
5
flush into the square
nuts
4
.
19344d_4
Push square nuts
4
includ-
ing adjusting bolts
5
into
the slot (B).
19344d_5
Place washers
6
under-
neath the screws
7
.
Place screws
7
in the mid-
dle of the oblong hole.
EADC-E12- 40
60
X
[mm]
78 98
Lightly clamp the adjusting
plate
2
to the mounting
surface with the screws
7
.
19344d_9
Use spanner (C) with
t
.
5 mm.
With t
,
5 mm, the possible
height compensator is smaller
by the difference (t
−
5).
19344d_6
Align planar surface gantry
(
Info
). Screw the adjust-
ing bolts
5
in or out
(h = 6 … 11 mm).
Observe sufficient screw-in
depth of the screws 7 (for
steel
≥
8 mm).
Tighten screws
7
1)
. Apply
counter pressure to the ad-
justing bolt
5
:
–
Do not twist the adjusting
bolt
5
.
–
Maintain alignment.
Check: alignment of the planar
surface gantry
8
.
19344d_7
1)
1)
Screw
7
and the tightening torque are designed for mounting on steel.
1
2
3
4
5
6
7
8
1
A
3
B
4
9.9 Nm
_
20 %
6
7
2
7
2
5
5
4
C
24 Nm
_
20 %
1)
5
7
5
7
C
C