Festo DGC G Series Скачать руководство пользователя страница 75

Страница: 75 / 136

27 / 44

Festo 7DGC-GFa_en

Replacing the cushioning components

4.1.6

Unfasten the lock nut on the cushioning components.

•

Note

The cushioning components can be replaced even when the end caps are
attached.

Unscrew the cushioning components from the end caps.

•

Insert the new cushioning components by repeating the steps in reverse

•

order and tighten them using the appropriate torque (see table).

Type

Torque

DGC-18-…-GF

3.0 Nm ±20%

DGC-25-…-GF

5.0 Nm ±20%

DGC-32-…-GF

8.0 Nm ±20%

DGC-40-…-GF

20 Nm ±20%

Replacing the sealing rings for the supply ports in the end caps

4.1.7

Unscrew and remove the plug screws for the supply ports from the end caps

•

and remove the sealing rings.

Note

The sealing rings can be replaced even when the end caps are attached.

Insert the new sealing rings in the supply ports by repeating the steps in

•

reverse order and tighten the plug screws using the appropriate torque
(see table).

Type

Torque

DGC-25-…-GF

11 Nm ±10%

DGC-32-…-GF

11 Nm ±10%

DGC-40-…-GF

50 Nm ±10%

Содержание DGC G Series









































































































































Результаты поиска

Содержание DGC G Series

Отзывы:

Похожие инструкции для DGC G Series

Бренды по названию

Популярные бренды

Festo DGC G Series, Инструкции по ремонту

Результаты поиска

Содержание DGC G Series

Отзывы:

Похожие инструкции для DGC G Series

Бренды по названию

Популярные бренды