Festo DGC G Series Скачать руководство пользователя страница 32

Страница: 32 / 136

32 / 48

Festo 07DGC-Ga_en

Clip the band reverser in the coupling.

•

Note

Make sure that the band reverser is aligned properly with the coupling
(see illustration).

Connect the coupling with the band reverser to the piston.

•

Note

Make sure that the coupling is properly aligned with the piston. The magnet
in the piston must be positioned on the left-hand side of the piston when the
coupling points backwards.

Grease the sealing rings and the band reverser.

•

Observe the greasing instructions in the table in chapter 4.2.2.
Assemble the linear drive as described in

•

chapter 4.2.2.

Replacing the buffer strips

4.2.4

Remove the buffer strips from the end caps.

•

Grease the backs of the new buffer strips and insert them into the end caps.

•

Replacing the sealing rings for the supply ports in the end caps

4.2.5

Unscrew and remove the plug screws for the supply ports from the end caps

•

and remove the sealing rings.

Note

The sealing rings can be replaced even when the end caps are attached.

Insert the new sealing rings in the supply ports by repeating the steps in

•

reverse order and tighten the plug screws using the appropriate torque
(see table).

Type

Torque

DGC-25-…-G

11 Nm ±10%

DGC-32-…-G

11 Nm ±10%

DGC-40-…-G

50 Nm ±10%

Содержание DGC G Series









































































































































Результаты поиска

Содержание DGC G Series

Отзывы:

Похожие инструкции для DGC G Series

Бренды по названию

Популярные бренды

Festo DGC G Series, Инструкции по ремонту

Результаты поиска

Содержание DGC G Series

Отзывы:

Похожие инструкции для DGC G Series

Бренды по названию

Популярные бренды