Festo DGC G Series Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 136

background image

27 / 48

Festo 07DGC-Ga_en

Pull the cover band out of the cylinder barrel.

•

Push the sealing band inwards and out of the guide slot (1) with a blunt

•

object and pull it out of the cylinder barrel (2).

Assembling the linear drive

4.2.2

When assembling a linear drive, wearing parts, such as the sealing band, cover band, seals and the complete piston,
can be replaced.
The wearing parts are ordered on the online spare parts catalogue (spareparts.Festo.com) quoting the appropriate part
number (dependent on the size of the linear drive).
The part number is an x-stroke part number. In addition to the part number, you must also specify the stroke of your
linear drive when ordering. The stroke can be determined from the type code on the name plate of the linear drive
(see order example below). Using this information you can calculate the necessary length or sealing band/cover band.

Cutting the new sealing band/cover band to length

The exact length of the sealing band and cover band is determined by the 0-stroke of the respective type and the stroke
of the linear drive. The stroke is specified by the type code on the name plate. Check the length of the new sealing band
and cover band and shorten them to length (0-hub + hub) as necessary. See order example.

Type

Length L

0

DGC-18-…-G

220 mm

DGC-25-…-G

250 mm

DGC-32-…-G

290 mm

DGC-40-…-G

335 mm



Example: DGC-25-330-G
0-stroke:

250 mm

Stroke:

330 mm

Length of the sealing band/cover band =
0- stroke = 580 mm

The length of the band calculated in this way is a theoretical value. Component tolerances may make it necessary to
adjust the length of the sealing band/cover band after installation.

Note

Sturdy general purpose scissors or metal shears are best for cutting the sealing band and cover band.

Warning

Do not bend the sealing band and the cover band as this may cause damage or tearing and reduce the service life of
the sealing band/cover band.

«
...
25
26
27
28
29
...
»

Содержание DGC G Series









































































































































Отзывы:

Нет отзывов

Похожие инструкции для DGC G Series

Бренд: Yamaha Страницы: 13

GA700 GA700 Series

Бренд: YASKAWA Страницы: 32

Бренд: IBM Страницы: 121

TRINORM 436 Series

Бренд: Emerson Страницы: 6

Бренд: TIS Страницы: 13

Бренд: Parker Страницы: 131

Бренд: RIB Страницы: 44

Бренд: AB Quality Страницы: 32

Бренд: Sanyo Denki Страницы: 119

Бренд: Alpha getriebebau Страницы: 34

Бренд: Danfoss Страницы: 22

VLT Integrated Servo Drive ISD 510 System

Бренд: Danfoss Страницы: 102

Бренд: ABB Страницы: 20

Бренд: ZF-DUOPLAN Страницы: 34

Бренд: Danfoss Страницы: 43

Бренд: Veichi Страницы: 193

ASD-M-0721 Series

Бренд: Delta Страницы: 645

Бренд: ANCA Motion Страницы: 164

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды