Festo CPX-FB38 Скачать руководство пользователя страница 25

Страница: 25 / 120

1. Installation

1−9

Festo P.BE−CPX−FB38−EN en 0804NH

Setting the operating mode with DIL switch

You can set the operating mode of the bus node with switch
element 1.1 of DIL switch

(see Tab.1/1):

Remote I/O operating mode

Operating mode Remote Controller

Operating mode

Setting DIL switch 1

Remote I/O operating mode

All functions of the CPX terminal are controlled directly by the
EtherCAT−IO controller or a superordinate PLC.

The bus node thereby takes over the connection to the
EtherCAT network.

DIL  1.1:  OFF
DIL  1.2:  OFF
(factory  setting)

Operating mode Remote Controller

Requirement:

a CPX−FEC is an integral part of the CPX terminal.

The FEC integrated in the terminal controls all functions.

The bus node thereby takes over the connection to the
EtherCAT network.

DIL 1.1: ON
DIL 1.2: OFF

Tab.1/1:

Setting the bus node operating mode with DIL switch 1

Содержание CPX-FB38

























































































































Результаты поиска

Содержание CPX-FB38

Отзывы:

Бренды по названию

Популярные бренды

Festo CPX-FB38, Электронное руководство

Результаты поиска

Содержание CPX-FB38

Отзывы:

Бренды по названию

Популярные бренды