manualshive.com logo in svg

Festo CPX-FB38, Электронное руководство

Поделиться
Скачать
Festo CPX-FB38 Скачать руководство пользователя страница 107

3.      Diagnosis

3−17

Festo  P.BE−CPX−FB38−EN    en  0804NH

3.5

Diagnosis  via  EtherCAT

3.5.1

Basic  information

Please  note

Availability  of  diagnosis  information  via  the  EtherCAT
network

 Note  that  the  diagnostic  information  shown  depends  on

the  settings  (see  section  1.2.2)  and  the  parameterisation
(see  section  2.5)  of  the  CPX  terminal  (see  also  section  3.1).

 Detailed  diagnosis  information  about  the  status  of

theCPX  terminal  are  available  to  the  EtherCAT  network
only  by  means  of  the  I/O  diagnosis  interface.

 Activate  the  I/O  diagnosis  interface  to  ensure  that  error

messages  of  the  CPX  terminal  are  automatically
displayed  in  the  EtherCAT  configuration  software,
e.g.Beckhoff  TwinCAT.

 Diagnostics  information  is  availabie  to  Beckhoff  TwinCAT

only  to  a  limited  extent  evenwith  activated  I/O  diagnosis
interface.  For  detailed  error  analysis,  use  the  handheld
unit,  the  Festo  Maintenance  Tool  or  your  requirements
according  to  application  programs  for  detailed  diag
nostic  functions.

Содержание CPX-FB38

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды