Festo CPX-FB23 Скачать руководство пользователя страница 52

Страница: 52 / 122

2. Commissioning

2−8

Festo P.BE−CPX−FB23−EN en 0308NH

2.1.2

Addressing rules

I/O counting method:

The address assignment of the inputs does not depend on
the address assignment of the outputs.

The counting method does not depend on the position of
the field bus node.

Counting is from left to right, depending on the module
type.

Modules  of  the  same  type  are  arranged  linearly  in  the
address  range,  providing  they  are  arranged  one  behind
the  other.

I/Os  of  the  same  type  each  occupy  their  own  station  in
ascending  order  without  gaps  (digital  I/Os,  analogue
I/Os,  I/Os  of  function  modules).

The following I/Os are assigned separately:

Remote Ready (RR, CC Link−specific reserved, always
lies in the last reserved station)

Diagnostic I/Os (only if configured)

Digital I/Os

Analogue I/Os, I/Os of funcion modules

The following table applies for the sequence of address
assignment:

Содержание CPX-FB23



























































































































Результаты поиска

Содержание CPX-FB23

Отзывы:

Похожие инструкции для CPX-FB23

Бренды по названию

Популярные бренды

Festo CPX-FB23, Электронное руководство

Результаты поиска

Содержание CPX-FB23

Отзывы:

Похожие инструкции для CPX-FB23

Бренды по названию

Популярные бренды