Festo CPX-E Series Скачать руководство пользователя страница 14

Страница: 14 / 28

Function

Festo – CPX-E-PB-EN – 2017-07 – English

2.5.3

Standard diagnostic information

The following diagnostic information can be requested from the DP master using function Slave_Diag of system
CPX-E

Tab. 3.7.

Station status 1

Bit

Meaning

Explanation

Diag.Station_Non_E xistent

1 = system CPX-E can no longer/not yet be addressed.
Possible causes:
–

Operating voltage not applied

–

Data transmission line interruped or disturbed

Diag.Station_Not_Ready

1 = system CPX-E not yet ready for data exchange.

Diag.Cfg_Fault

1 = Configuration data obtained from the master does not agree with
the configuration data from system CPX-E.

Diag.Ext_Diag

1 = Diagnostic message exists.
Possible causes:
–

Cable fracture on input/output module

–

Short circuit/overload of electrical outputs, etc.

Diag.Not_Suppor ted

1 = System CPX-E does not support the requested function

Diag.Invalid_Slave_Response

Always 0 (permanently set by system CPX-E)

Diag.Prm_Fault

1 = Last parameterisation telegram incorrect

Diag.Master_Lock

Always 0 (permanently set by system CPX-E)

1) Bits that refer to system CPX-E are bolded.

Tab. 2.12

Station status 2

Bit

Meaning

Explanation

Diag.Prm_Req

1 = Master must reconfigure system CPX-E

Diag.Stat_Diag

1 = Master must request diagnostic data until this bit is set to 0

–

Always 1 (permanently set by system CPX-E)

Diag.WD_On

1 = Response monitoring (watchdog) activated

Diag.Freeze_Mode

1 = Freeze activated

Diag.Sync_Mode

1 = Sync activated

Reserved

–

Diag.Deactivated

Always 0 (permanently set by system CPX-E)

1) Bits that refer to system CPX-E are bolded.

Tab. 2.13

Station status 3
Bit

Meaning

Explanation

0 … 6

Reserved

–

Diag.Ext_Diag_Overflow

1 = system CPX-E has more diagnostic messages than can be buffered
or master contains more diagnostic messages than it can buffer.

Tab. 2.14

Содержание CPX-E Series





























Результаты поиска

Содержание CPX-E Series

Отзывы:

Похожие инструкции для CPX-E Series

Бренды по названию

Популярные бренды

Festo CPX-E Series, Описание

Результаты поиска

Содержание CPX-E Series

Отзывы:

Похожие инструкции для CPX-E Series

Бренды по названию

Популярные бренды