Module error [
P
]
1)
LED
(red)
Significance
Remedy
Parameterisation error (error number 29)
Check parameterisation and adjust.
Lit
Encoder error
2)
(error number 108)
è
Off
Normal operating status
–
1) Lights up until the module initialisation is completed.
2) If monitoring via parameters is activated.
Tab. 8 Module error
Status of input I0
…
I3 [X0], [X1]
LED
(green)
Significance
Remedy
Lit
Input active (logic 1)
1 signal at input
–
Off
Input inactive (logic 0)
0 signal at input
–
Tab. 9 Status of input I0 ... I3 [X0], [X1]
Normal operation of encoder [X2]
LED
(green)
Significance
Remedy
Lit
Encoder in normal operation
–
Off
Encoder error
(
è
Tab. 11 Encoder error [X2]) or module
not initialised
–
Tab. 10 Normal operation of encoder [X2]
Encoder error [X2]
LED
(red)
Significance
Remedy
Encoder error (error number 108)
Cable break
Check cables and connections.
Tracking error
Reduce frequency of input pulses.
Lit
Zero pulse error
Check “pulse/zero pulse” parameter and
adjust
è
Description of module.
Off
Encoder in normal operation
(
è
Tab. 10 Normal operation of encoder
[X2]) or module not initialised
–
Tab. 11 Encoder error [X2]
Normal operation of encoder supply [X3]
LED
(green)
Significance
Remedy
Lit
Encoder supply in normal operation
–
Off
Error in encoder supply
(
è
Tab. 13 Error in encoder supply [X3]) or
module not initialised
–
Tab. 12 Normal operation of encoder supply [X3]
Error in encoder supply [X3]
LED
(red)
Significance
Remedy
Lit
Short circuit/overload of encoder supply
(error number 2)
Check cables and connections.
Off
Encoder supply in normal operation
(
è
Tab. 12 Normal operation of encoder
supply [X3]) or module not initialised
–
Tab. 13 Error in encoder supply [X3]
12
Disposal
ENVIRONMENT!
Send the packaging and product for environmentally sound recycling in accord-
ance with the current regulations
è
13
Technical data
General technical data
General technical data for
automation system CPX-E
Description of automation system CPX-E
è
1.1 Further applicable documents
Dimensions (length x width x
height)
[mm]
124.3 x 18.9 x 76.6
Product weight
1)
[g]
88
Mounting position
Vertical/horizontal
Ambient temperature
[°C]
–5 … +60 (–5 … +50)
2)
Storage temperature
[°C]
–20 … +70
Air humidity
(non-condensing)
[%]
0 … 95
Assigned address space
(inputs/outputs)
[bytes]
12/2
Degree of protection in
accordance with EN 60529
IP20
Protection against electric
shock (protection against dir-
ect and indirect contact in
accordance with
IEC 60204-1)
Through the use of PELV circuits
(protected extra-low voltage)
Electromagnetic compatibil-
ity
To EN 61000-6-2/-4
Module code/submodule
code (CPX-E-specific)
174/10
Module identification
E-1CI
1) Including linkage
2) for horizontal mounting position
Tab. 14 General technical data
Power supply
Operating voltage supply
U
EL/SEN
[V DC]
24 ± 25 %
Intrinsic current consumption
at nominal operating voltage
24 V from U
EL/SEN
[mA]
15
Reverse polarity protection
Yes
Encoder supply 5 V DC /
24 V DC
[V DC]
5 ± 5 % / 24 ± 25
%
Continuous nominal current
of encoder supply
[mA]
500
Short circuit protection of
encoder supply
Yes
Undervoltage identification
Response threshold U
EL/SEN
[V DC]
<
16
Hysteresis U
EL/SEN
[V DC]
0.3 … 0.5
Response threshold, encoder
supply 5 V DC
[V DC]
4.5
Tab. 15 Power supply
Encoder inputs
Max. input frequency of encoder signals
1)
Differential
[MHz]
2
Single ended
[kHz]
250
Max. debounce time of encoder inputs
1)
Differential
[ns]
125
Single ended
[µs]
1
1) Dependent on the connection type of the encoder, "differential" or "single ended"
Tab. 16 Encoder inputs
