Festo CPX-CTEL-4-M12-5POL Скачать руководство пользователя страница 14

Страница: 14 / 59

System overview, CTEL system

Festo – P.BE-CPX-CTEL-EN – 1601b – English

LED

Significance

Behaviour

Off

CPX system-internal communication OK

Lights up red

Several causes are possible:

–

CPX system starts momentarily, display then turns off

–

General fault

X1 … X4

Off

No connection to a device

Lights up green

Device connected, communication OK

Flashes green

Several causes are possible:

–

Connection established to the device, diagnostics running

–

I/O length of the recognised device is too large

Lights up red

Device error. Several causes are possible:

–

Connection to the device interrupted

–

Error in the I-Port communication

Flashes red

Compatibility error. Several causes are possible:

–

An incompatible device is connected to the corresponding

I-Port.

–

The corresponding port is deactivated, but a connected

device is recognised.

All four LEDs flashing

red

Configuration error. Several causes are possible:

–

Invalid configuration (e.g. through exceeding of the available

address space)

–

Device has been replaced by another device type

Tab. 2.3

Monitoring of the load voltage U

VAL

(PL) takes place in the devices and is passed on to the

CTEL master module.

Since all connected devices use this LED, the display of an error has priority over the dis

play “OK” (LED illuminated green).

The I-Port at which the error has occurred can be determined through the FMT/MMI using

the diagnostic messages.

Information on eliminating the displayed errors:

5.2.2 Diagnostic/error messages by CPX error numbers.

Содержание CPX-CTEL-4-M12-5POL




























































Результаты поиска

Содержание CPX-CTEL-4-M12-5POL

Отзывы:

Похожие инструкции для CPX-CTEL-4-M12-5POL

Бренды по названию

Популярные бренды

Festo CPX-CTEL-4-M12-5POL, Описание

Результаты поиска

Содержание CPX-CTEL-4-M12-5POL

Отзывы:

Похожие инструкции для CPX-CTEL-4-M12-5POL

Бренды по названию

Популярные бренды