manualshive.com logo in svg

Festo CPX-CMAX, Описание, Страница: 13 / 98

Поделиться
Скачать
Festo CPX-CMAX Скачать руководство пользователя страница 13

1

Safety and requirements for product use

Festo – P.BE-CPX-CMAX-SYS-EN – en 2017-09b – English

13

Specified standards

Version status

EN 60204-1:2006-06/A1:2009-02

ISO 8573-1:2010

Tab. 1.1

Standards specified in the document

1.2.5

Permitted CPX bus nodes and control blocks

The following CPX bus nodes and control blocks are approved for operation with the CMAX axis control­

ler starting with the revisions named here (at the time this description was printed). Older revisions are

not supported and can lead to unpredictable behaviour.

Current information on this 

è

 catalogue from Festo (

è

 www.festo.com/catalogue).

Observe the notes on the software status in the documentation for the bus node or con­

trol block.

Bus node/

control block

Protocol

Approved revision

1)

Max. number

2)

CMAX

CPX-CEC

(Control block)

Revision 5 and above

8

CPX-FEC

Revision 19 (R19) and above

8

CPX-CEC-C1

Revision 7 (R7) and above

8

CPX-CEC-M1

Revision 3 (R3) and above

8

CPX-FB6

Interbus

Revision 22 (R22) and above

1

CPX-FB11

DeviceNet

Revision 20 (R20) and above

8

CPX-FB13

PROFIBUS-DP

Revision 23 (R23) and above

8, 7

3)

CPX-FB14

CANopen

Revision 20 (R20) and above

4

CPX-M-FB20

Interbus

Revision 2 (R2) and above

1

CPX-M-FB21

Interbus

Revision 2 (R2) and above

1

CPX-FB23-24

CC-Link (function module F23)

Revision 19 (R19) and above

4

CC-Link (function module F24)

8

CPX-FB32

EtherNet/IP

Revision 14 (R14) and above

8

CPX-FB33

PROFINET

Revision 7 (R7) and above

8

CPX-M-FB34

Revision 7 (R7) and above

8

CPX-M-FB35

Revision (R20) and above

8

CPX-FB36

EtherNet/IP

Revision 5 (R5) and above

8

CPX-FB38

EtherCAT

All

8

1)

Revision status (Rev...) 

è

 Product label.

2)

The maximum number within a CPX terminal can be further restricted through the available address range.

3)

If acyclic services (DPV1) are used, a maximum of 7 CMAX modules are permitted.

Tab. 1.2

Required revisions

Содержание CPX-CMAX



































































































Отзывы:

Нет отзывов