Festo CMMP-AS-***-M0 Series Скачать руководство пользователя страница 68

Страница: 68 / 294

EtherCAT interface

Festo – GDCP-CMMP-M3/-M0-C-CO-EN – 1510b – English

4.10

Error Control

The EtherCAT CoE implementation for the motor controller CMMP-AS-...-M3 monitors the following

error statuses of the EtherCAT fieldbus:

–

FPGA is not ready when the system is started.

–

A bus error has occurred.

–

An error has occurred on the mailbox channel. The following errors are monitored in this case:

–

An unknown service is requested.

–

A protocol other than CANopen over EtherCAT (CoE) is to be used.

–

An unknown Sync Manager is addressed.

All of these errors are defined as corresponding error codes for the motor controller CMMP-AS-...-M3. If

one of the above-mentioned errors occurs, it is transmitted to the controller via a “Standard Emergency

The CMMP‐AS‐...‐M3/-M0 motor controller with the EtherCAT interface supports the following function:

–

Application Controller determines a defined error message number as a result of an event

(Error Control Frame telegram from the controller).

4.11

Emergency Frame

The master and slaves exchange error messages via the EtherCAT CoE emergency frame. The CoE emer

gency frames are used for direct transfer of the “Emergency Messages” defined under CANopen. The

CANopen telegrams are simply tunnelled through the CoE emergency frames, as is the case for SDO

and PDO transmission.

6 bytes

2 bytes

1 byte

2 bytes

5 bytes

1...n bytes

Mandatory Header

Standard CANopen Emergency Frame

Optional

Mailbox Header

CoE Header

Error Code

Error Register

Data

Fig. 4.7

Emergency Frame: telegram structure

Element

Description

Mailbox Header

Data for mailbox communication (length, address and type)

CoE Header

Identifier of the CoE service

ErrorCode

Error Code of the CANopen EMERGENCY Message

Chapter 3.5.2

Error Register

Error Register of the CANopen EMERGENCY Message

Tab. 3.9

Data

Data content of the CANopen EMERGENCY Message

Data (optional)

Additional optional data. As only the standard CANopen emergency frames are

supported in the CoE implementation for the motor controller CMMP-AS-...-M3,

the “Data (optional)” field is not supported.

Tab. 4.14 Emergency Frame: elements

As the “Emergency Messages” received and sent via CoE are simply forwarded to the CANopen protocol

implemented in the motor controller, all error messages can be looked up in the chapter B.

Содержание CMMP-AS-***-M0 Series







































































































































































































































































































Результаты поиска

Содержание CMMP-AS-***-M0 Series

Отзывы:

Бренды по названию

Популярные бренды

Festo CMMP-AS-***-M0 Series, Руководство пользователя

Результаты поиска

Содержание CMMP-AS-***-M0 Series

Отзывы:

Бренды по названию

Популярные бренды