Festo 548076 страница 54 Скачать руководство пользователя | Manualshive

Страница: 54 / 92

background image

54 / 92

Festo 7DHTGd_en

4

Repair steps

This chapter describes the dismantling, repair and assembling of the rotary indexing table DHTG-…-A and
DHTG-…-A-P4 / P4E4 / P4L12. Depending on the cause of the defect to be eliminated, it may be necessary to replace
several components.
Where possible, it is advisable to dismantle the rotary indexing table from the system entirely before carrying out the
repair.
Before starting the repair, dismantle any attachments in accordance with the instructions in the accompanying operating
instructions.
Keep your working environment clean and tidy.
Before dismantling the rotary indexing table, the cause of the failure must be investigated to prevent repeated and pre-
mature failure. A rotary indexing table which is used as intended will not normally exhibit any premature signs of failure.
This investigation is not necessary in the case of non-premature failure (fatigue time). However, the condition of the rota-
ry indexing table (general condition, etc.) should always be checked.
In case of uncertainty, we recommend replacing all the components mentioned to rule out reciprocal effects during later
operation.
In the event of premature failure of the rotary indexing table, the conditions of use should be examined more closely.
The following possibilities should be considered, among other things:

– Overloading

– In case of overloading, the application parameters (load, speed) should be adjusted accordingly.

– Ambient conditions/material resistance

– Check whether the ambient temperature is within the permissible range.
Check the chemical and physical ambient conditions for harmful substances, such as dust, abrasive particles, cooling

lubricants, solvents, ozone, radiation, water-soluble substances, greases and oils, etc.

Note

The repair should preferably be carried out on a stable and flat work surface with storage for small parts.

To prevent damage to the O-rings and other components, do not use pointed or sharp-edged assembly tools.

4.1

Preparatory steps

Before dismantling the rotary indexing table, the locking cylinders must be moved downwards and the ball bearing
released.
1. Ensure that no supply line is connected at connection B.
2. Vent connection A, to move the locking cylinder downwards.

4.2

Visual inspection

Check the rotary indexing table for visible damage, which could impair the function, e.g. severe dents. The entire rotary

indexing table must be replaced if there are signs of significant damage.

«
...
52
53
54
55
56
...
»

Содержание 548076





























































































Отзывы:

Нет отзывов

Похожие инструкции для 548076

Бренд: Panasonic Страницы: 30

Бренд: UFO Страницы: 16

Бренд: Baker Страницы: 82

Бренд: T-Rex Страницы: 13

Бренд: VBM Страницы: 36

Бренд: W&H Med Страницы: 122

Бренд: Raymarine Страницы: 124

Бренд: Raymarine Страницы: 192

Бренд: Varytec Страницы: 5

Бренд: Saab Страницы: 98

Бренд: Kaixin Страницы: 89

Бренд: Ultraflex Страницы: 52

Бренд: Palmgren Страницы: 12

Бренд: Bartscher Страницы: 20

TOTAL KNEE 1900

Бренд: Össur Страницы: 58

Бренд: CAB Страницы: 30

C-HB-A-LB2-SCCT Series

Бренд: C-LITE Страницы: 9

X-431 Torque HD

Бренд: Launch Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды