Ferris 5901879 Скачать руководство пользователя страница 47

Страница: 47 / 56

Not for

Reproduction

2. Clean the battery terminals and cable ends with a wire

brush until shiny.

3. Reinstall the battery and reattach the battery cables,

positive [+] cable first (B, Figures 66 & 67 ).

4. Coat the cable ends and the battery terminals with

petroleum jelly or non-conducting grease.

Checking Battery Voltage

A voltmeter can be used to determine condition of the battery.

When the engine is off, the voltmeter shows battery voltage,

which should be 12 volts. When the engine is running, the

voltmeter shows voltage of charging circuit which normally is

13 to 14 volts.
A dead battery, or one too weak to start the engine, may not

mean the battery needs to be replaced. For example, it may

mean that the alternator is not charging the battery properly.

If there is any doubt about the cause of the problem, see

your authorized Ferris servicing dealer. If you need to replace

the battery, follow the steps under

Cleaning the Battery and

Cables

Charging the Battery

WARNING

Keep open flames and sparks away from the battery; the

gasses coming from it are highly explosive. Ventilate the

battery well during charging.

A dead battery or one too weak to start the engine may be

the result of a defect in the charging system or other electrical

component. If there is any doubt about the cause of the

problem, see your authorized Ferris servicing dealer.
To charge the battery, follow the instructions provided by the

battery charger manufacturer as well as all warnings included

in the OPERATOR SAFETY section of this manual. Charge

the battery until fully charged. Do not charge at a rate higher

than 10 amps.

Jump Starting with Auxiliary (Booster) Battery

Jump starting is not recommended.

Troubleshooting

While normal care and regular maintenance will extend

the life of your equipment, prolonged or constant use may

eventually require that service be performed to allow it to

continue to operating properly.
This troubleshooting guide lists the most common problems,

their causes and remedies.
Refer to

Maintenance Procedures

for instructions on how

to perform most of these minor adjustments and service

repairs yourself. If you prefer, all of these procedures can be

performed for you by your local authorized dealer.

WARNING

Remove ignition key prior to performing maintenance on the

unit.

To avoid serious injury, perform maintenance on the unit

or mower deck only when the engine is stopped and the

parking brake is engaged.
Always remove the ignition key, disconnect the spark plug

wire(s) and fasten it away from the plug(s) before beginning

the maintenance, to prevent accidental starting of the

engine.

Troubleshooting Charts

Troubleshooting the Zero-Turn Rider

Problem: Engine will not turnover or start.

Cause

Remedy

Parking brake not engaged.

Engage parking brake.

PTO (electric clutch) switch in ON

position.

Place in OFF position.

Ground speed control levers not in

"NEUTRAL" position.

Move ground speed control levers to

the "NEUTRAL" position.

Out of fuel.

If engine is hot, allow it to cool, then

refill the fuel tank.

Engine flooded.

Carburated Models:

Move choke

control to closed position.

Fuel

Injected Models:

See authorized

dealer.

Fuse blown.

Replace fuse.

Battery terminals require cleaning.

Clean the battery terminals.

Battery discharged or dead.

Recharge or replace

Wiring loose or broken.

Visually check wiring & replace

broken or frayed wires. Tighten loose

connections.

Solenoid or starter motor faulty.

See authorized service dealer.

Safety interlock switch faulty

Replace as needed. See authorized

service dealer.

Spark plug(s) faulty, fouled or

incorrectly gapped.

Clean and gap or replace. See

engine manual.

Water in fuel.

Drain fuel and replace with fresh fuel.

Gas is old or stale.

Drain fuel and replace with fresh fuel.

Содержание 5901879

























































Результаты поиска

Содержание 5901879

Отзывы:

Похожие инструкции для 5901879

Бренды по названию

Популярные бренды

Ferris 5901879, Руководство оператора

Результаты поиска

Содержание 5901879

Отзывы:

Похожие инструкции для 5901879

Бренды по названию

Популярные бренды