Ferris 5901843 Скачать руководство пользователя страница 38

Страница: 38 / 56

Not for

Reproduction

ferrismowers.com

9. Check the balance of the blade. If either end of the

blade moves downward the end that moves downward

is heavier than the other. Sharpen the heavy end until

balance is achieved.

10. Repeat the process until the mower blade remains in the

horizontal, level position.

Installing the Mower Blades

CAUTION

Laceration hazard.

Mower blades are sharp.
Always wear gloves when handling, or working near, mower

blades.

1. Install each mower blade with the air lifts (C, Figure 44)

pointing up towards the mower deck as shown in Figure

44 and secure with the mower blade mounting bolt (A)

and flat washer (B).

2. Wedge a wooden block (D) between the mower blade

and the mower deck housing to keep the mower blade

from turning and torque the blade mounting bolt to 120 ft.

lbs (163 Nm).

Seat Adjustment (Suspension Seat)

This series of mower has multiple suspension seat options: a

standard suspension seat (A, Figure 45), and a suspension

seat that has lumbar and back angle adjustments (B). If your

unit features a suspension seat, identify your suspension seat

and follow the correct instructions below. See Figure 45.

Seat Adjustment Lever (Forwards / Backwards):

The

seat can be adjusted forward and back. Move the forwards /

backwards seat adjustment lever (C), position the seat as

desired, and release the lever to lock the seat in position.

Seat Adjustment Knob (Suspension/Ride Comfort):

The

seat adjustment knob (D) adjusts the suspension of the seat

(ride comfort). Turn the adjustment knob until the display

scale has a reading that matches the weight of the operator.

Lumbar Adjustment Knob:

Turn the lumbar adjustment

knob (E) until the desired amount of lumbar is achieved.

Back Angle Adjustment Lever:

Move the back angle

adjustment lever (F), position the back angle of the seat as

desired, and then release the lever.

Ground Speed Control Lever Adjustment

The control levers can be adjusted in three ways. The

alignment of the control levers, the placement of the control

levers (how close the ends are to one another), and the

height of the control levers can be adjusted.

To Adjust the Control Lever Alignment

Loosen the mount bolts (A, Figure 46) and pivot the control

lever(s) (C) to align with each other.

Содержание 5901843

























































Результаты поиска

Содержание 5901843

Отзывы:

Похожие инструкции для 5901843

Бренды по названию

Популярные бренды

Ferris 5901843, Руководство оператора

Результаты поиска

Содержание 5901843

Отзывы:

Похожие инструкции для 5901843

Бренды по названию

Популярные бренды