Ferris 5901756 Скачать руководство пользователя страница 33

Страница: 33 / 40

Not for

Reproduction

6. Locate the parking brake jam nuts (A, Figure 40) and the

parking brake rod (B). Note that in Figure 40, the left rear

wheel has been removed.

7. Use a 9/16" wrench to break the parking break jam nuts

(A) loose from the parking brake rod (B). Do not remove

the jam nuts from the rod, only loosen them.

8. Use an 11/16" wrench on the head of the parking brake

rod. Screw the rod until the distance (D, Figure 41)

between the washer (F) and the parking brake arm (G)

measures 3/8".

9. Use a 9/16" wrench to re-tighten the parking brake jam

nuts (A).

10. Reattach the left rear wheel and use a 13/16" wrench

tighten the wheel nuts.

11. Repeat Steps 2-7 on the right side of the unit. With the

parking brake engaged, the compressed springs (C) on

each side of the parking brake arm should measure 1

7/8" (E).

Note:

If this does not correct your braking problem, see

your authorized dealer.

Cleaning the Battery and Cables

This unit is equipped with a maintenance-free BCIU1 battery.

WARNING

Keep open flames and sparks away from the battery.

• Be careful when handling the battery.
• Avoid spilling electrolyte.
• Keep flames and sparks away from the battery.
• When removing or installing battery cables, disconnect

the negative cable FIRST and reconnect it LAST. If not

done in this order, the positive terminal can be shorted

to the frame by a tool.

1. Remove the rubber strap and battery box cover.

Содержание 5901756









































Результаты поиска

Содержание 5901756

Отзывы:

Бренды по названию

Популярные бренды

Ferris 5901756, Руководство оператора

Результаты поиска

Содержание 5901756

Отзывы:

Бренды по названию

Популярные бренды