Ferris 5901756 Скачать руководство пользователя страница 22

Страница: 22 / 40

Not for

Reproduction

ferrismowers.com

6. Disengage the parking brake. Slowly squeeze the ground

speed control levers towards the maximum forward speed

control bar to start driving the unit forward.

7. Turn the spreader ON/OFF switch (C) to the "ON"

position.

8. Pull the hopper gate control to the "OPEN" position.
9. To stop the spreading operation, push the gate lever

to the "CLOSED" position, and reverse the steps listed

above.

Operating the Shaker

The shaker/agitator vibrates the granular hopper to release

additional granular material. The shaker is activated by the

momentary shaker switch (A, Figure 25). To activate the

shaker/agitator, press and hold the momentary shaker switch.

To deactivate the shaker, release the momentary shaker

switch.

Operating the Sprayer

The sprayer has a pattern width of 12' when both the left and

right spray booms are deployed and all of the spray nozzles

are activated. The effective pattern width is 10' wide, which

allows the same pass width as the spreader. For this reason,

the spreader and spraying systems may be operated at the

same time. Product should be mixed in the tank at a rate that

matches the coverage area, not the spray tank size.
1. Add the required liquid materials to the spray tank or

tanks.

2. While standing on the operator's platform, make sure that

all the sprayer/spreader controls are OFF, the parking

brake is engaged, and then insert the ignition key into the

ignition switch and turn to the START.

3. Use the liquid material tank selector lever (A, Figure 26)

to select which tank you want to spray liquid fertilizer

from. You can choose the left, right, or both tanks.

4. Activate the spray system by moving the spray pump on/

off switch (E) to the ON position.

5. Set the spray pressure adjustment control (C) to the

desired pressure setting when the unit is at full throttle

and the system is spraying. The spray pressure can be

read by viewing the spray system pressure gauge (D). It

is common for the spray system pressure to rise above

the set pressure setting if the pump is activated and the

boom control levers are shut off so that no liquid material

is released from the nozzles.

This unit is equipped with Teejet AIXR spray tips.

• To achieve an application rate of 1/4 gallon liquid

material per 1000 square feet, set the spray system

pressure to 20 psi and the ground speed to 5 mph.

This will produce extra coarse droplets.

• To achieve an application rate of 1/3 gallon liquid

material per 1000 square feet, set the spray system

pressure to 30 psi and the ground speed to 5 mph.

This will produce very coarse droplets.

For other application rates, refer to the spreader/sprayer

calibration chart found on the underside of the operator

thigh pad.

6. Observe the direction of the wind and plan an application

path that allows the spraying to occur downwind. Avoid

spraying in windy conditions as the spray may carry to

non-target areas.

7. Disengage the parking brake.
8. Slowly squeeze the ground speed control levers towards

the maximum forward speed control bar to start the unit

driving forward.

Содержание 5901756









































Результаты поиска

Содержание 5901756

Отзывы:

Бренды по названию

Популярные бренды

Ferris 5901756, Руководство оператора

Результаты поиска

Содержание 5901756

Отзывы:

Бренды по названию

Популярные бренды