Ferris 5901756 Скачать руководство пользователя страница 14

Страница: 14 / 40

Not for

Reproduction

ferrismowers.com

• To release the spray boom, open the spring latch.
• To close the spray boom, fold the boom towards the

spring latch and ensure the spring latch closes over the

pin on the end of the boom.

Liquid Material Tank Selector Lever

This lever controls which tank from which liquid fertilizer will

be drawn. The left, right, or both tanks can be selected. Move

the lever to the position of the desired tank(s).

Spray System Pressure Gauge

This gauge displays the pressure of the spraying system

to the operator. To adjust the spray system pressure, see

the

Spray Pressure Adjustment Control

Spray Pressure Adjustment Control

This knob adjusts the pressure of the liquid material spray

system. To adjust, turn the knob left or right.

• Turn the knob to

clockwise

to increase the pressure.

• Turn the knob

counter-clockwise

to decrease the

pressure.

Boom Control Levers/Spray Toggle Valves

These levers control the boom sections. There are left, right,

and center boom sections. Each boom section contains two

sprayers. The boom sections can be used simultaneously or

separately depending on spraying needs.

• To turn activate the sprayers in a boom section, pull its

lever to the ON position.

• To turn deactivate the sprayers in a boom section, push

its lever to the OFF position.

Spray Pump On/Off Switch

This switch (A, Figure 11) activates the sprayer pump.

• Press the switch to the ON position to start the sprayer

pump.

• Press the switch to the OFF position to stop the sprayer

pump.

See

Operating the Sprayer

for additional instructions.

Spreader Control Functions and

Locations

The information below briefly describes the function of

individual controls. Spreading requires the combined use of

several controls applied in specific sequences. To learn what

combination and sequence of controls to use for various tasks

see the

Operation

section.

Содержание 5901756









































Результаты поиска

Содержание 5901756

Отзывы:

Бренды по названию

Популярные бренды

Ferris 5901756, Руководство оператора

Результаты поиска

Содержание 5901756

Отзывы:

Бренды по названию

Популярные бренды