Ferris 5600001 Скачать руководство пользователя страница 6

Страница: 6 / 36

Not for

Reproduction

www.ferrismowers.com | www.snapperpro.com

Safety Rules & Information

2-Bag & 3-Bag Collector Hood

Decal, Container, Icons (Sewn into fabric of
collector hood)

Safety Icons

Danger - Rollover hazard:

• Do not operate up or down slopes or without the

front counter balance weights.

• Operate on slopes only if under 10 degrees.

• Always use front counterbalance weights while

operating on slopes.

Warning - Amputation and thrown objects hazard:

• To avoid injury from rotating parts (of the blower).

• Stay clear of parts and keep all shields and guards

in place.

• Operate blower only with entire collection system

installed and latched closed.

Warning - Amputation and thrown objects hazard:

• Disengage the blower (blades) and remove

the ignition key, wait for all parts to stop before
disconnecting or unlatching any parts attached to
blower or collection system.

Warning - Read the Operator’s Manual.

Caution - Always wear hearing protection when
operating.

Warning - Loss of traction and control hazard:

• Do not operate with only the collection system

installed.

• Do not operate with only the front counter balance

weights installed.

• Operate only with both the entire collection system

and front counter balance weights installed and the
collection system closed and latched.

Danger - Dismemberment:

• This machine can crush and cut. Keep hands

away from belts and pulleys.

Danger - Amputation and thrown objects hazard:

• To avoid injury from rotating blades, stay clear of

deck edge and keep others away.

Содержание 5600001





































Результаты поиска

Содержание 5600001

Отзывы:

Похожие инструкции для 5600001

Бренды по названию

Популярные бренды

Ferris 5600001, Руководство оператора

Результаты поиска

Содержание 5600001

Отзывы:

Похожие инструкции для 5600001

Бренды по названию

Популярные бренды