background image

28

www.ferrisindustries.com

NOTE: Diesel fuel, if permitted to stand unused for 
extended periods (30 days or more), may develop 
gummy deposits which can adversely affect the fuel 
pump and injector tubes and cause engine malfunction. 
To avoid this condition, add a diesel fuel stabilizer to the 
fuel tank and run the engine a few minutes, or drain all 
fuel from the unit before placing it in storage.

STARTING AFTER LONG TERM 
STORAGE

Before starting the unit after it has been stored for a long 
period of time, perform the following steps.

 1.  Remove any blocks from under the unit.

 2.  Install the battery if it was removed.

 3.  Unplug the exhaust outlet and air cleaner.

 4.  Fill the fuel tank with fresh fuel.  See engine manual 

for recommendations.

 5.  See engine owner’s manual and follow all 

instructions for preparing engine after storage.

 6.  Check crankcase oil level and add proper oil if 

necessary.  If any condensation has developed 
during storage, drain crankcase oil and refill.

 7.  Inflate tires to proper pressure.  Check fluid levels.

 8.  Start the engine and let it run slowly. DO NOT run at 

high speed immediately after starting. Be sure to run 
engine only outdoors or in well ventilated area.

DIESEL FUEL RECOMMENDATIONS

Fuel companies provide fuel tailored to meet the existing 
weather conditions.  These fuels change at the start of 
the predominant season according to regional weather 
trends.

Winter fuels are tailored to give ease of starting for cold 
weather.  Summer fuel may be somewhat heavier than 
winter fuel resulting in slightly better fuel economy and 
power.  Spring and fall fuel is an average blend between 
winter and summer blend.

For these reasons an effort should be made to purchase 
fuels in such quantities that they are not carried over 
into the next season.  Using the wrong blend of fuel can 
cause problems with the engine.

Refer to the engine manufacturer’s manual for specific 
fuel recommendations.

STORAGE

Temporary Storage (30 Days Or Less)

Remember, the fuel tank will still contain some fuel, so 
never store the unit indoors or in any other area where 
fuel vapor could travel to any ignition source.  Fuel vapor 
is also toxic if inhaled, so never store the unit in any 
structure used for human or animal habitation.

Here is a checklist of things to do when storing your unit 
temporarily or in between uses:

  •  Keep the unit in an area away from where children 

may come into contact with it. If there’s any chance 

of unauthorized use remove the ignition key.

  •  If the unit can’t be stored on a reasonable level 

surface, chock the wheels.

  •  Clean all grass and dirt from the mower.
  •  If temperature is expected to drop below 35 degrees, 

refer to Long Term Storage, Item 2.

Long Term Storage (Longer Than 30 

Days)

Before you store your unit for the off-season, read the 
Maintenance and Storage instructions in the Safety 
Rules section, then perform the following steps:

 1.  Drain crankcase oil while engine is hot and refill with 

a grade of oil that will be required when unit is used 
again.

 2.  Use an Antifreeze tester to check the cooling 

system’s level of protection.  Read the instructions 
on the Antifreeze container for the appropriate ratio 
of water to Antifreeze for your geographical area.

 3.  Prepare the mower deck for storage as follows:

    a. Remove mower deck from the unit.

    b. Clean underside of mower deck.

    c. Coat all bare metal surfaces with paint or light coat 

of oil to prevent rusting.

 4.  Clean external surfaces and engine.

 5.  Prepare engine for storage. See engine owner’s  

manual.

 6.  Clean any dirt or grass from cylinder head, engine 

housing and air cleaner element.

 7.  Cover air cleaner and exhaust outlet tightly with 

plastic or other waterproof material to keep out 
moisture, dirt and insects.

 8.  Completely grease and oil unit as outlined in the 

Regular Maintenance section.

 9.  Clean up unit and apply paint or rust preventative to 

any areas where paint is chipped or damaged.

 10. Be sure the battery is filled to the proper level 

with water and is fully charged. Battery life will be 
increased if it is removed, put in a cool, dry place 
and fully charged about once a month. If battery is 
left in unit, disconnect the negative cable.

11. Drain fuel system completely or add a diesel fuel 

stabilizer to the fuel system. If you have chosen to 
use a fuel stabilizer and have not drained the fuel 
system, follow all safety instructions and storage 
precautions in this manual to prevent the possibility 
of fire from the ignition of diesel fumes. Remember, 
diesel fumes can travel to distant sources of ignition 
and ignite, causing risk of explosion and fire.

WARNING

Never store the unit, with diesel fuel in engine 
or fuel tank, in a heated shelter or in enclosed, 
poorly ventilated enclosures.  Diesel fumes 
may reach an open flame, spark or pilot light 
(such as a furnace, water heater, clothes dryer, 
etc.) and cause an explosion.

Handle diesel fuel carefully. It is highly 
flammable and careless use could result in 
serious fire damage to your person or property.

Drain fuel outdoors into an approved container 
and away from open flame or sparks.

Operation

Not 

for  

Reproduction

Содержание 5100/61R AUS/NZ





























































Отзывы: