DUO
DUO
DUO
DUO
DUOX CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
DUO
DUO
DUO
DUO
DUOX CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
DUO
DUO
DUO
DUO
DUOX CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
DUO
DUO
DUO
DUO
DUOX CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
X CITYLINE KIT 3-24L
ENGLISH
1. CONFIGURE AS MASTER PANEL
The programming is always done from the MASTER panel and there can only be one in
the complete installation.
Configuring the master panel:
Press the
SW1
button 3 times quickly, it is activated as
a MASTER panel and a confirmation tone sounds (beep-beep).
2. PROGRAMMING THE TELEPHONE
1
< 2,5 min
5
A
2
1. With the telephone connected, press the programming button (you will hear a beep).
Upon releasing it, you will hear the entrance into programming.
2. Press the call-to-residence button. A programming confirmation is produced.
* The telephone will not function until it has been programmed.
Programming Button
3. DEACTIVATE MASTER MODE ON THE PANEL
Once having completed the terminal's configuration, deactivate the MASTER panel to
avoid accidentally reprogramming terminals.
Deactivating the master panel:
Press the
SW1
3 times consecutively fast, and it will
deactivate the panel as MASTER. A deactivation tone sounds (beep-bop).
QUICK PROGRAMMING GUIDE
5 way cable
Connecting the keypad:
a)
With the disconnected power, use the 5 way cable to connect the keypad as shown in
the diagram.
b)
Reconnect the power supply. Now you can program the required parameters with the
keypad.
c)
Before performing the operation to disconnect the keypad, remove the power.
9
8
7
6
5
4
3
2
1
A
B
0
ON
DL2
EXIT
MIC
AUDIO
AMPLIFIER
AMPLIFICADOR
DUOX
PACK EXTENSION
B
D
A
C
E
LANGUAGE
IDIOMA
18Vdc
SW1 PROG
CN9 TAMPER
CN1
LED
DL2
ONE
P2
+
B
B
+12
C
NC
NO
-
BS
S
P1
C
NC
NO
F
BUS
GND
CN3
CN2
TO
ONE
VERSION :
SW1
CN9
CN1
CN1
CN1
ENTRADA/INPUT
ARRIVÉE/EINTRITT
CN1
UP
SALIDA/OUTPUT
SORTIE/AUSGANG
CN2
MÓDULO TECLADO
KEYPAD MODULE
MODULE CLAVIER
TASTATURMODUL
PUT
NTRITT
CN1
CN1
4. ENCODING PANELS
Whenever there are
more
than one panel (to a block) you must program the
panel
number
, but for this you need key 7439.
If your installation is characterised by having
General Inputs, Interior Blocks and/or
Sub-blocks
, and must also program:
We recommend filling in the amplifier's sticker once each panel is programmed.
Examples:
5. RESET TO DEFAULT VALUES (if necessary)
A 4444 (beep-beep) 13 (beep) 1 (beep-beep)
Position
03
04
05
Adjustments Parameter Possible Values [default]
Comments
Panel type
Block no. (BK)
Sub-Block no. (BS)
0:
Sub-Block (SB)
[1]:
Block (BK)
2:
General Entrance (EG)
00-99
[00]
00-99
[00]
Configuration of the panel
type
Block number the panel
belongs to
Sub-Block number the
panel belongs to
The entry panel's parameters can be programmed on the keypad.
1.1 Access programming:
A + 4444
(default code).
If the code is correct, a confirmation tone sounds (beep-beep).
1.2 Configuring the different parameters
The configuration of a parameter is done by entering:
two digits of its position,
and a
beep is heard and the
desired value
(1,2,3 or 4 digits relative to the parameter function).
If the value is correct, a confirmation tone sounds (beep-beep) and the new value is
saved. If not correct you will hear the error sound (beep-bop).
In order to exit the programming press 'A' when we are entering the menu's parameter
number. You can also exit by waiting 60 seconds without pressing any key.
Configuration of a parameter:
A + access code for progr po possible values
Configuration of a panel number:
A + 4444 + 06 + 0-9
Example:
•
Change panel number 2:
A 4444 (beep-beep) 06 (beep) 2 (beep-beep)
PROGRAM THE PANEL NUMBER
,
Panel number
Position
06
Adjustments Parameter Possible Values [default]
Comments
Panel No. (PL)
0-9 [0]
PL
Nº
SB
BK
EG
Nº
TYPE
BK
X
3
PL
Nº
SB
BK
EG
Nº
TYPE
BK
X
2
01
PL
Nº
SB
BK
EG
Nº
TYPE
BK
X
3
02
01
General Entrance and
panel number 3
Block 1 and panel number 2
Sub- block 2 and panel
number 3, belonging to
block 1
PL
Nº
SB
BK
EG
Nº
TYPE
BK
2
