8
EN
compatible with this power tool could pose a
risk to persons.
•
Never remove cuttings, wood chips, etc.
from the cutting area while the power tool is
running.
Always guide the tool arm back to the
neutral position first and then switch the power
tool off.
•
Do not touch the saw blade after working
before it has cooled.
The saw blade becomes
very hot while working.
•
Never make warning signs on the machine
unrecognisable.
•
If laser radiation hits your eye, you must
close your eyes and immediately turn your
head away from the beam.
•
Do not use any optical instruments such
as binoculars to view the radiation source.
Doing so can damage your eye.
•
Do not direct the laser beam at persons who
are looking through binoculars or similar
instruments.
Doing so can damage their eye.
•
Do not make any modifications to the laser
equipment.
The setting options described in
these operating instructions can be used safely.
•
Do not stand in line with the saw blade in
front of the power tool.
Always stand to the
side of the saw blade. This protects your body
against possible kickback.
•
Keep hands, fingers and arms away from the
rotating saw blade.
•
Do not reach one hand across the other
when in front of the tool arm.
•
Avoid overheating of the saw teeth. When
the saw blade overheats, stop the machine.
Allow the saw blade to cool down before using
the machine again.
•
Replace damaged or worn saw blades
immediately.
•
Only use saw blades that match the
specifications given in this operating manual
and that have been tested and marked in
accordance with EN 847-1.
•
When sawing curved or round workpieces,
these must be especially secured against
slipping. At the cutting line, there should
be no gap between the workpiece, fence
and saw table.
If necessary, you will need to
manufacture special fixtures.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
• As a supply for this machine always use an
unloaded line and/or an extension cable with
conductors of at least 1,5 mm2 and protected
with a 16 A fuse. Be sure that this extension
cable is not longer than 20 metres.
• This machine can be switched to the
singlephase network (230-240 V/50 Hz). If you
are in doubt about the earth of the electricity
provisions, consult an electrician first.
2. MACHINE INFORMATION
Intended use
The electro tool is intended as a stationary machine
for making straight lengthways and crossways cuts
in wood. Horizontal mitre angles of -45° to +45° as
well as vertical bevel angles of -45° are possible.
Technical specifications
Mains voltage
230-240 V, 50Hz
Capacity
1900 W
Machine class
II (double insulated)
No load speed
5.000/min
Saw blade measurement
254x2.4x30mm
Angle for mitring
45º (left and right)
Angle for bevelling
45º (only left)
Mitre saw maximum sawing capacity:
Mitre 0º, Bevel 0º
70x310mm
Mitre 45º, Bevel 45º
40x210mm
Mitre 45º, Bevel 0º
70x210mm
Mitre 0º, Bevel 45º
40x310mm
Weight
12.55 kg
Lpa (sound pressure)
94.5+3 dB(A)
Lwa (acoustic capacity)
108.4+3 dB(A)
Vibration level
<2.5 m/s2
Содержание MSM1040
