6
Ferm
OPERATIONAL SAFETY
Warning!
Be aware this planer can produce fine
dust, which can be hazardous to your health.
Always use a suitable mask, eye protection, and other per-
sonal protection equipment. Use dust extraction during wor-
king and cleaning.
Concentrate
Routine and repetition can lead to mistakes. Remember
that a slight lack of concentration can result in serious
injuries in a split second.
Keep work area clean
Cluttered areas and benches invite injuries.
Consider the work environment
Do not expose power tools to rain or use them in damp
or wet locations. Keep work area well lit. Do not use
power tools in the presence of flammable liquids, vap-
ours or gases.
Guard against electric shock
This unit contains dangerous voltages. Use a RCD (resi-
dual current device) to provide protection against elec-
trical shock. Prevent body contact with grounded sur-
faces (e.g. pipes, radiator, ranges or refrigerators).
Keep children and pets away
Do not let children or pets come into contact with the
tool, extension cable or work area.
Do not force the tool
It will work better and safer at the rate for which it was
intended.
Use the right tool
Do not force small tools or attachments to do the job of a
heavy-duty tool. Do not use tools for purposes for which
they were not intended; for example do not use a circular
saw for cutting trees or logs.
Do not abuse the cable
Never carry the tool by the cable or pull it to disconnect
it from the power socket. Keep the cable away from heat,
oil and sharp edges. Do not touch the metal plug pins
when connecting or removing the plug.
Do not over-reach
Keep a proper footing and balance at all times.
Disconnect tools from power supply
When not in use, before servicing and when changing
accessories such as blades, bits and cutters.
Always switch off and unplug the planer from the
power supply before making adjustments or chan-
ging belts.
Remove adjusting keys and wrenches
Ensure that they are removed from the tool before swit-
ching on.
Avoid unintentional starting
Do not carry plugged in tools with your finger on the
switch. Check that the switch is off before plugging in to
socket.
Extension cables
Use only three core earthed extension cables suitable
for the power input of the tool (minimum cable size
1.5mm
2
). Plug into an earthed socket only.
When using a cable reel unwind it fully. Do not use long
extension cables.
Outdoors use
If the tool is suitable to be used outdoors, only use an
extension cable intended for outdoor use and marked
accordingly. Use a RCD (residual current device) to pro-
vide protection against electrical shock. Do not use in
rain or damp conditions.
Connect a dust extraction device
Whenever there are facilities for fitting a dust or fume
extraction system, make sure it is connected and used.
Use recommended accessories
The use of an accessory or attachment other than
recommended in the instructions or catalogue may pre-
sent a risk of personal injury. Use an extension cable with
a minimum conductor size of 1.5mm
2
.
When using a cable reel unwind it fully.
Ferm
3
A damaged part or guard should be properly repaired by
an authorised service centre, unless indicated otherwise
in the instruction manual. Have defective switches
replaced by an authorised service centre. Do not use a
tool if the switch does not turn on and off.
Have your tool repaired by an expert
This appliance is manufactured in accordance with rele-
vant safety standards. Only experts must carry out repai-
ring of electrical appliances, otherwise considerable dan-
ger for the user may result.
Storing tools
When not in use tools should be stored in the dry, out of
reach of children.
ELECTRICAL INFORMATION
This product is complete with a pre-wired mains plug, if
the plug needs replacing follow these instructions.
This planer is double insulated in accordance with EN
50144 therefore no earth wire is required.
Wire correctly
The wires in the mains lead are coloured in the following
way:
BLUE
•
Neutral
BROWN
•
Live
Securing wires
Secure wires carefully and firmly to the correct termi-
nals. Secure the mains cable in the plug cord grip firmly
Fit a 5-amp fuse. If a 13amp (BS1363) plug is used a (BS
1362) ASTA approved 5-amp fuse must be fitted.
Recycle/Dispose of old plug and cable
Prevent inadvertent connection to socket and risk of
electric shock.
ENVIROMENT
Recycle the packaging according to the identification
marks on it.
At the end of the product or its accessories life please
recycle where facilities exist. Phone the Helpline for cur-
rent advice on recycling.
Helpline
For any questions relating to operational or safety
matters contact:
Ferm Customer Helpline on:
0115 966 1199
Monday-Friday
8am – 6pm
Saturday
9am – 1 pm
GUARANTEE
The guarantee conditions can be found on the separately
enclosed guarantee card.
We declare under our sole responsability that this
product is in conformity with the following
standards or standardized documents
EN50144-2-14, EN50144-1
EN55014-1, EN61000-3-2,
EN61000-3-3, EN55014-2
in accordance with the regulations:
98/37/EEC
73/23/EEC
89/336/EEC
from 01-04-2001
GENEMUIDEN NL
W. Kamphof
Quality department
CE
ı
DECLARATION OF CONFORMITY
(UK)
Blue
(Neutral)
Green & Yellow
(Earth)
Brown
(Live)
Fuse
(5 Amp)