background image

1.1   Safety information

1.1.1  A word to the technician

Read and understand the safety section in this

service manual before operating or servicing the

machine. Read and understand the safety sections

in the manuals for all attachments before

operating or servicing attachments. The technician

has the key to safety. Good safety practices

protect everyone.
Study the safety information in this service

manual. Make the safety information a working

part of the safety program. The safety information

in this service manual applies specifically to this

type of machine. Always do all other usual and

customary safe working precautions. Remember -

The technician has the responsibility for safety.

Good safety practices can prevent serious injury or

death.
The safety section points out some basic safety

situations that can occur during the operation and

maintenance of the machine. The safety section

also suggests possible ways to deal with these

situations. The safety section does not replace

safety practices in other parts of this service

manual.
Practice good safety to help prevent injury or

death.
Learn how to operate the machine and how to use

the controls correctly.
Do not let other persons operate the machine

without instruction and training.
Follow all safety precautions and instructions in

the manuals and on safety signs affixed to the

machine and all attachments.
Use only approved attachments and equipment.
Make sure the machine has the correct equipment

needed by the local regulations.

WARNING:
An operator should not use alcohol or
drugs which can affect their alertness
or coordination. An operator on
prescription or 'over the counter'
drugs needs medical advice on
whether or not they can properly
operate machines. If any attachments
used on this equipment have a
separate Operator Manual, see that
manual for other important safety
information.

GUID-AC91CCF6-1FF8-4A85-97A1-2D1562806825-high.jpg [High]

Fig. 1  

[V]

GUID-3C35D58D-1F5D-4B85-A915-C7BB48F47262 [V1]

1. General

Rubber Track Tractor 

1-3

79037272A

Find manuals at https://best-manuals.com

Содержание Vario MT 938




















































Отзывы: