FENDT 938 Vario MT Скачать руководство пользователя

Страница: 32 / 51

Rotate the new oil filter carefully until the gasket touches the opposite surface.

Tighten the oil filter ¾ rounds (or one (1) full round, if the height of the oil filter used is 260 mm). Use

an appropriate tool for tightening if necessary.

Wipe off any oil run onto the chassis.

Do a check for the quantity of oil in the engine.

If it is necessary, add oil.

Start the engine. Do not race.

10.

Make sure that no oil is leaking from the oil filter.

11.

Take the used oil filter to a proper disposal point.

1.6.4.3 Update the engine software

Engine software updates bring new features to the engine controller that improve the performance of the

engine, update diagnostic features and help to protect the engine and its emission components over the

engine lifetime.

Procedure

Use the EDT and examine, if new software is available for the machine.

Update the engine software, if possible.

1.6.4.4 How to recognize an engine with hydraulic lash adjusters
IMPORTANT:

Do not adjust the valves of an

engine, which has hydraulic lash adjusters!

An engine with hydraulic lash adjusters has a

cylinder block, which has drillings for oil ways for

each hydraulic lash adjuster. If the cylinder block

has oil ways, there are screw plugs on the oil ways

in the cylinder block.
The screw plugs are in the same locations, where

the hydraulic lash adjusters or valve tappets are.

For example, one location is above the engine

plate.

(1)

Screw plug

NOTE:

The same cylinder block is used in some

engines, which do not have the hydraulic lash

adjusters.

GUID-D19C4F02-BB60-4F75-A73E-9224770F6F33-low.svg [Low]

Fig. 24

Procedure

Examine the cylinder block for screw plugs on oil ways.

Result

If the cylinder block has no screw plugs, the engine does not have hydraulic lash adjusters.

If the cylinder block has screw plugs, examine the screw head of the screw plug.

Result

If the screw head of the screw plug has two levels, the engine does not have hydraulic lash adjusters.

GUID-1E23D7F6-0FCA-4D43-9400-74EA1657CCF5 [V2]

GUID-83FFFD66-C378-4F12-BBB7-6A1055F7CD94 [V2]

1. General

Rubber Track Tractor

1-29

79037495A

Содержание 938 Vario MT




















































Результаты поиска

Содержание 938 Vario MT

Отзывы:

Похожие инструкции для 938 Vario MT

Бренды по названию

Популярные бренды

FENDT 938 Vario MT, Руководство по обслуживанию мастерской

Результаты поиска

Содержание 938 Vario MT

Отзывы:

Похожие инструкции для 938 Vario MT

Бренды по названию

Популярные бренды