background image

GENERAL INFORMATION

Operator's Manual Combines  FENDT 5275 C-6335 C- EN - LA327317011 - 09/2011

1-13

FIELD OPERATIONS

¥

DANGER:

To provide a better view, certain 

illustrations in this manual show the 
machine with the safety guards or covers 
removed.

Keep all guards in place.

1.) Before starting work the operator should 

familiarise himself thoroughly with all machine 
controls. 

Ensure that the table has been properly 
attached. 

The combine manufacturer shall 

not be held liable if non-genuine tables are 
used.

2.) Always drive the combine at a speed which, 

depending on ground conditions, provides the 
necessary safety.

When working on 

rough ground

, proceed with 

great care to ensure machine stability.

Always use the seatbelts provided on the 
operator seat and on the other seat, if an 
instructor is present.

¥

DANGER:

 Risk of overturning.

3.) When taking the combine to work on slopes, 

the operator must be thoroughly familiar with 
machine controls and with working on sloping 
grounds. Drive at slow speed, in particular 
while turning and when the grain tank is full.

The combine must not be used in the following 
situations (this list is not exhaustive):

• When maximum allowable inclination is 

exceeded (see page 1-4)

• If correct securing of the cutting table to the 

main crop elevator with the safety stops has 
not been checked

• If correct tyre pressures have not been 

checked

• If proper operation of the levelling system 

has not been verified

• If the ground is not sufficiently firm or 

features sudden surface changes, or the 
tyres do not have enough grip on the 
ground

• If working close to the edge of ditches or 

steep drops.

 

4.) If the machine tends to tilt forward when 

working on slopes, lower the cutting table 
completely.

5.)

Take turns at moderate speeds 

(3-4 Km/h).

¥

DANGER:

 Risk of squeezing, cutting or 

getting trapped.

6.) If any moving part becomes blocked or 

jammed,

 release it only when the engine is 

switched off and all drives have come to a 
complete stop. Never push the crop into the 
main crop elevator using hands, feet or any 
other means. This may cause severe injury 
or death.

¥

DANGER:

 Risk of breathing in dust.

7.) Threshing dust may cause allergic lung 

diseases. The dust may also contain residues 
of pesticides injurious to health. Keep the cab 
doors shut when threshing. Wear a protection 
mask when carrying out service work involving 
exposure to dust (cab filters, rotary screen etc.) 
and when working with compressed air. 

Содержание 5275 C
































Отзывы: