[9]
[18]
[19]
[20]
[21]
[10]
[14]
[15]
[16]
[17]
mini port
micro port
[12]
[3]
[1]
[2]
[2] Rolling axis
[3] Panning axis
[4] Cross arm
[5] Vertical arm
[6] Joystick
[16] Corss bar
[17] Hand grip
[15] Connector
[14] Thumb screw
[13] Handle
[12] Function interface
[21] Mini allen key
[22] Wireless remote control
[23] Wireless remote control receiver
[20] USB connector
[19] USB cable（micro port）
[18] USB cable（mini port）
[11] Adapter(Clamping plate)
[10] Adjusting clamping plate
[9] Thumb screw for fixing lens
[8] Socket connector
[7] Function button
[1] Tilting axis
Instruction Manual V2.0
3-Axis Gimbal for Mirrorless Camera
Note
1. Please do not remove the holder screws fully to avoid wrong installation.
2. For detachable camera lens, please intall it with the thumb screw for fixing lens to avoid vibiration.
Warm tip
1. Please mount the adjusting clamping plate, camera lens, memory card, etc. and then remove the
lens cover before the balance adjustment.
2. In order to prevent the gimbal damage from improper mounting. Please don’t fully unscrew the
screws that secure the motor while adjust the balance. Unscrew till loose is advisable.
3. To help you remember the position after adjustment, we remain a 20mm scale.
1. Product Overview
2. Installation
3. Balance Adjustment
MG is one kind of 3-axis handheld gimbal especially for mirroless cameras. Simple and clean design
integrated strong operation function, easy to switch among more using ways. The easiest operation
experience. Pan/Tilt/Roll 3-axis 360 degrees coverage, Giving you ultimate experience while using the
MG for shooting.
STEP 1
Balance adjustment of the tilting axis
STEP 2
Balance adjustment of the rolling axis
In order to achieve the desired effect of the MG gimbal, the first use or replace the camera / lens,
or change the camera position, weight, size, appearance, need to adjust the balance.
Mount the camera on the adjusting
clamping plate, fix the tilting, rolling
position, and keep it at the horizon
level, and turn the lens down.
Observe the camera status.
If camera leans to front or back, then
loosen 4 screws on the adapter, and
adjust the camera to the opposite
position, until the camera can mount
properly.
As shown, if the camera is tilted toward A, the
fixed plate live A direction, if tilted toward B, the
fixed plate should be live B direction.
As shown, if the camera is tilted toward A, the camera
live A direction, if tilted toward B, the camera should be
live B direction.
As shown, if the camera is tilted toward A, move the cross arm to A direction, if tilted toward B, move
the cross arm to B direction.
Make sure to tighten the screws after the fixing plate is adjusted.
Adjust center of gravity of the camera horizon
position in tilting axis, after the adjustment of the
center of gravity in vertical position.
Adjust center of gravity of the camera horizon position in rolling
axis, after the adjustment of the center of gravity in tilting axis.
The screws on the bottom of the adjusting clamping、
in a relaxed state.
Fix the tilting, rolling position, and keep it at the
horizon level. Make the camera lens forward. And
observe the camera status.
If camera leans to front or back, then move the camera
to the opposite position , until the camera can mount
properly.
After the adjustment tighten the screws on the MG plate
and the lens retaining ring .
Fix rolling position manually and keep the camera at the horizon level, leave hold of it and observe the
camera status.
If camera leans to left or rihgt, then loosen 4 screws on the scale, and adjust the cross arm to the
opposite position of the cross arm, until the camera keep the current position after adjustment.
[6]
[2]
[4]
[1]
[3]
[5]
[22]
[23]
[7]
[8]
* The default use
way is handheld
* This product does not contain cameras
and camera equipment category
The showing camera only for reference.
Attention:
Please complete the installation before power on the gimbal
(1) Adjust center of gravity of the
camera vertical position in tilting axis.
(2) Adjust center of gravity of the camera horizon position
in tilting axis.
Screw
Thumb screw
Thumb screw
Cross
arm
Tips:
Please don’t fully unscrew
the screws that secure the motor
while adjust the balance.
Unscrew till loose is advisable.
Tips:
Please don’t fully unscrew
the screws that secure the motor
while adjust the balance.
Unscrew till loose is advisable.
a.
b.
c.
a.
b.
c.
a.
b.
c. After the adjustment tighten the screws on cross arm.
A
B
B
A
A
A
B
A
B
Thumb screw
A
B
B
A
Camera
Camera
Adapter
(Clamping plate)
The bottom
of adapter
(Clamping plate)
Adapter
(Clamping plate)
[13]
[12]
[4]
[9]
[11]
[10]
Tilting 360°
Rolling
360°
Panning 360°
18650
18650
3
4
5
Installation of the camera
Camera balance
adjustment
Installation of handle
2
Installation of adjusting clamping plate
Adjusting clamping plate light slip along the slideway to the
suitable position. If use a long lens, please install the thumb
screw for fixing lens[9] after installing the adjusting clamping.
Correctly place the camera to the
adjusting clamping, fixing it by the
thumb screw [14] trough the screw
holes on the bottom of the adjusting
clamping.
Adjust the adjusting
clamping to make the camera close
to the tilting motor
, fixing the adjusting
clamping by the thumb screw [14].
Please install the camera close
to the tilting.
In order to achieve the desired
effect of the MG gimbal, the
first use or replace the
camera / lens, or change the
camera position, weight, size,
appearance, need to adjust
the balance.
Thumb
screw
Tilting
Adjusting clamping plate
Thumb screw
for fixing lens
Adapter
1
Insert the batteries
Remove the handle, insert
2 pcs 18650 batteries and
tighten the screw.
Warm tip:
if the first time to use or
replace the camera / lens, or change
the camera position, weight, size,
appearance, it is only fixed, without
tightening the middle screw too tight,
in order to facilitate the balance after
adjustment.
Balance adjustment
procedures, please refer to the
"Balance Adjustment" section.
MG combined with the connector and handle can be used to achieve a variety of ways, choose the
installation method according to your need.
6
Starting and shutdown
Power on / off
Start:
Press the bottom switch, power on the gimbal,
and then single tap on the function button to
start it.
Off:
Press the bottom switch again to turn off.
If the power is too low, the gimbal will turn off.
After replacing the batteries, click the function
button to restart the gimbal.
Start the gimbal
Dual Handheld
Installation
Portable
Installation
Please locked hand
grip after installation
!
!
Handheld
Disassembly
Connector
Handle
Corss bar
Hand grip
Lock
catch