background image

IRB20 Inverted Microscope Bulb & Fuse Replacement

12

Fein 

TROUBLE

POSSIBLE CAUSE

SOLUTION

Coarse focusing knob 

is too tight.

Tension knob is too loose.

Tighten it a little.

Stage declines itself, 

cannot stay on the 

focal plane when 

observing.

Tension knob is too loose.

Tighten it a little.

Coarse focusing knob 

can’t rise.

The limit stop knob is locked.

Loosen the knob.

Coarse focusing knob 

can’t decline.

The base of the condenser is too low.

Raise the base.

Cannot move the 

slide smoothly.

The slide is not fixed correctly.

Adjust it 

The movable specimen holder is not fixed 

properly.

Adjust it

The image moves 

obviously when 

touching the stage.

The stage is fastened incorrectly.

Fasten the stage correctly.

The LED light does 

not work.

No power supply.

Check the connection of the 

power cable.

The LED bulb is not installed correctly.

Install it correctly.

The LED bulb is burnt out.

Replace it.

The bulb burns out 

frequently.

The wrong bulb is being used.

Replace it with the correct bulb.

The illumination is 

not bright enough.

The wrong bulb is being used. 

Replace it with the correct bulb.

The illumination adjustment is not set in a 

bright position.

Adjust the illumination knob to 

intensify the light.

Troubleshooting

Содержание RB20

















Отзывы: