Feig Electronic ID ISC.LRU3000 Скачать руководство пользователя

Страница: 60 / 193

OBID

i-scan

UHF

Manual

ID ISC.LRU3000/3500

FEIG ELECTRONIC GmbH

Page 60 of 193

H90202-7e-ID-B.docx

DB-ADR

(OperatingMode.BufferedReadMode.DataSource.FirstDataBlock)

(OperatingMode.NotificationMode.DataSource.FirstDataBlock)

(OperatingMode.ScanMode.DataSource.FirstDataBlock)

Address of first data block. Range: 0x00...0xFF.

DB-N

: (OperatingMode.BufferedReadMode.DataSource.NoOfDataBlocks)

(OperatingMode.NotificationMode.DataSource.NoOfDataBlocks)

(OperatingMode.ScanMode.DataSource.NoOfDataBlocks)

Number of data blocks. Range: 0x01...0x20. The data block size in the Buffered Read
Mode is always 2 bytes.

D-START: (OperatingMode.ScanMode.DataSource.FirstByte)

This parameter defines the first byte in the raw data (defined by DB-ADR and D-LGT),
which will be transferred in Scan-Mode. To transfer the whole data block D-START must be
set to 0.

NOTE:

The size of one data block depends on the type of Transponder.

D-LGT:

(OperatingMode.ScanMode.DataSource.NoOfBytes)

D-LGT defines the length of raw data which are transmitted in the Scan-Mode.

Number of

data bytes

to be transferred, starting with the D-START.

Example:
data block

Output Data

0x23

0x45

0x67

0x89

NOTE:

If Wiegand / DataClock is selected as Scan Mode Interface D-LGT indicates the number of
Bits to be transmitted.

A plausibility check is performed by writing this parameter to the Reader. If an error occurs the Reader

answers with STATUS = [0x11].

Byte

Data

0x01

0x23

0x45

0x67

0x89

0xAB

0xCD

0xEF

D-START = 1

D-LGT = 4

Содержание ID ISC.LRU3000


































































































































































































Результаты поиска

Содержание ID ISC.LRU3000

Отзывы:

Похожие инструкции для ID ISC.LRU3000

Бренды по названию

Популярные бренды

Feig Electronic ID ISC.LRU3000, Руководство пользователя

Результаты поиска

Содержание ID ISC.LRU3000

Отзывы:

Похожие инструкции для ID ISC.LRU3000

Бренды по названию

Популярные бренды