Feider FPSI140A Скачать руководство пользователя страница 2

 

Safety Caution

 

 

This  welding  machine  complies  with  international  safety  standards.  Safety  is  an  important 

issue  in  the  design  and manufacture  of  equipment.  There  are  always  some  risks  associated 

with  the  use  of  welding  equipment.  In  order  to  ensure  your  safety  and  that  of  your  work 

environment, please read carefully and observe these safety instructions. 

 

1. General safety points 

•  Properly  install  the  unit  in  accordance  with  the  standards  and  instructions  given  in  this 

manual. 

• Do not touch the tool and the pliers when you have hands without protective gloves, with 

wet hands, or when you have wet clothes. 

• Make sure there is proper insulation between you and the floor and the room. 
• Make sure your work position is secure. 
• Connect the welding machine only to a grounded electrical network. 
• Respect the recommended size of the fuses 
• Avoid putting the welding machine inside a container, container or similar. 
• Avoid placing the welding machine on a wet surface and avoid working on a wet surface. 
• Do not expose the power cable to water. 
• Make sure that the cable holder or welding electrode is not squeezed by heavy objects and 

that they are not exposed to sharp edges or a hot workpiece. 

• Make sure the welding electrode holder is  not  damaged or faulty.  If this is  the case, the 

media must be replaced immediately. 

• Remember that the cable, plugs and other electrical equipment should only be installed or 

replaced by a qualified electrician or authorized engineer. 

• Turn off the welding machine when not in use. 

 

Smoke - Possibility of causing damage to health! 

• Keep any part of the body away from the fumes caused by the operation. 
• Provide good ventilation or use a smoke extractor during operation to avoid gas breathing. 
• Always wear a protective mask when using the machine. 
•  Take  precautions  when  working  on  metals  or  materials  containing  lead,  cadmium,  zinc, 

mercury or beryllium.

 

 

X-ray arc - Ability to damage your eyes and burn your skin! 

 Use the supplied welding mask, glass filter and protective equipment to protect your eyes 

Содержание FPSI140A
















Отзывы: