manualshive.com logo in svg

Feider Machines FTREN220V, Инструкция по эксплуатации, Страница: 17 / 32

Поделиться
Скачать
Feider Machines FTREN220V Скачать руководство пользователя страница 17

ENGLISH (Original instructions)

6. Turn the lever clockwise fully and a quarter turn back to keep looseness for adjusting the chain tension.

7. Turn the adjusting dial to adjust the chain tension.

8. Turn the lever clockwise until the sprocket cover is secured then return it to the original position.

The saw chain may become loose after many hours of use. From time to time check the saw chain tension before use.

1. Press and fully open the lever until it clicks. Turn it counterclockwise a little to loosen sprocket cover lightly.

2. Lift up the guide bar tip slightly and adjust the chain tension. Turn the adjusting dial to the "-" direction to loosen,

turn to the "+" direction to tighten. Tighten the saw chain until the lower side of the saw chain fits in the guide bar rail as

illustrated.

1.Lever 2.sprocket cover

Adjusting saw chain tension

Carry out the procedure of installing or removing saw chain in a clean place free from sawdust and the like.

Do not tighten the saw chain too much. Excessively high tension of saw chain may cause breakage of saw

chain, wear of the guide bar and breakage of the adjusting dial.

A chain which is too loose can jump off the bar and it may cause an injury accident.

1.Lever 2.Sprocket cover

1.Adjusting dial 2.Guide bar 3.Saw chain

17

Содержание FTREN220V

































Отзывы:

Нет отзывов