background image

ORIGINAL INSTRUCTIONS >EN

6) Frequently monitor the charger and battery pack while connected.
7) Unplug the charger and disconnect it from the battery pack when finished.
8) Allow the battery pack to cool completely before using it.
9) Store the charger and battery pack indoors, out of reach of children.

NOTE

: If the battery does not fit properly, disconnect it and confirm that the battery pack is the

correct model for this charger as shown on the specification chart. Do not charge any other battery pack or
any battery pack that does not securely fit the charger.

NOTE:

If battery is hot after continuous use in the tool, allow it to cool down to room temperature

before charging. This will extend the life of your batteries.

NOTE

: Remove battery pack from charger stand which use your thumb or fingers, press the battery’s

release button in and pull the battery pack off at the same time.

Battery capacity indicator

There are battery capacity indicators on the battery pack; you can check the capacity status of the battery if
you squeeze the button. Before using the machine, please press switch trigger to check if the battery is full
enough for properly working.

WARNING! Before making any adjustments ensure the drill is switched off with the direction

of rotation selector in the center position

1. Remove the battery: press the battery release latch in and at the same time pull the battery pack off.

2.

To insert the battery, push the battery pack onto the contacts of the tool.

6.2 REPLACING THE APPLIANCE ATTACHMENT

WARNING!

Secure the appliance against switching on (see “Switching on/off”) or remove the rechargeable battery from
the appliance. There is an injury hazard if the device is switched on accidentally.

Removing appliance attachment

1) Push the unlocking lever (5) into position as far as the stop and then hold it in this position.
2) Pull the unlocked appliance attachment off.
3) Allow the unlocking lever (5) to slide back into position.

Fitting appliance attachment

4) Push the appliance attachment along the guide rail into the motor unit (6). It locks into place audibly.
5) Allow the unlocking lever (5) to slide back into position.
6) Check that the appliance attachment is secure by pulling on it.

6.3 SWITCHING ON/OFF

1). Switching on: Press the on/off switch (11).By using the on/off switch (11) you can progressively control
the speed. Gentle pressure: low speed Increase pressure: higher speed.
2). Switching off: Release the on/off switch (11). If you place the direction switch (7) in the middle position,
the device is secured against being switched on.

13

Содержание FPVSS18V4IN1























Отзывы: