background image

ACCESSORIES AVAILABLE FROM YOUR DEALER:

 

SURFACE RIDER TUBE & COVER FASTENING KIT 

TUBE AND COVER FASTENERS (10 sets per pouch)

REEL STRAPPING (10 Straps 26” per pouch)

REEL STRAPPING (1 - 50’ Roll)

COVER STRAPS (2 x 54”  per pouch)

WHITE PROTECTIVE SHEET (24’ x 3 1/2‘ sheet)

MID-GRIP PULL ROPE 

 
 

 

 

MID-GRIP PULL ROPE ACCESSORY (FG-MPR)  

(Available from your Dealer)

For ease of pulling cover on pool, we suggest using the Mid-Grip Pull Rope
accessory.  This easily attaches to the cover as shown at the left. 

Makes pulling cover

onto the pool easier.

Clips to side for easier 

access when cover is 

rolled.

FG-SRFAS

FG-PFS

FG-RS26

FG-RS50

FG-BS2

FG-WPS

FG-MPR 

FG-BS2

Safe Use of Your Solar Reel:

 

Solar Reel systems are designed solely to remove solar covers and are not made to support people or
any other weight.

 

 

Solar covers must be completely removed before entry into the pool.  Under no circumstances, should 
one swim in a pool partially covered with the solar cover. 

Tubes are made of non-anodized aluminum and will discolor over time.  This does not affect performance. 

 

 

 

 

Care and Storage:

 

Check screws periodically and tighten, if necessary

.  The solar reel may be stored outside for the winter.  

It is not recommended to disassemble it for storage inside.  

 

 

 

 

 

·

·

·

NEW DESIGN VACUUM HOSE REEL 

Available through your local dealer

SOLD 

WITH

 35’ OF PLASTIFLEX VACUUM HOSE  (FG-VHGH) 

 

or choose 

THE VACUUM HOSE REEL  (FG-VHG)

FG-VHG

FG-VHGH

Holds up to 50’ of 1 1/2“ Vacuum Hose
Durable polyethylene construction
Also for Pool Backwash Hose, Electrical 
Cord (100’) or Garden Hose (100’)

CLIP

CLIP

END
LOOP

END

LOOP

ROPE

ROPE

Содержание Surface Rider

Страница 1: ...idth of the pool from the outside edges of top rail and subtract 4 10 cm to ensure ends of system are 1 2 wider than outside of top rail Ends must sit loosely on pool System Ends must be FULLY inserted into end tubes Fig 1 Handle End 2 Rubber Pads 2 Rubber Pads Center Tube s Axle End End Tube End Tube Note THIS STEP REQUIRES A TOTAL OF 12 SELF DRILLING SCREWS Do not pre drill holes Minimum Maximum...

Страница 2: ...u move the cover away from the pool and fold it bubbles in on a flat surface Choose either Fig 10 or Fig 11 D Strap end Fig 8 Strap Plate Strap Plate Strap Plate Insert each end firmly and fully into the tubes Attach each end by installing one self drilling screw through drill line 1 2 5 cm from the tube end at BOTH ends see Fig 7 Insert Screw A B Additional instructions and hardware are included ...

Страница 3: ...ms are designed solely to remove solar covers and are not made to support people or any other weight Solar covers must be completely removed before entry into the pool Under no circumstances should one swim in a pool partially covered with the solar cover Tubes are made of non anodized aluminum and will discolor over time This does not affect performance Care and Storage Check screws periodically ...

Страница 4: ...on of incidental or consequential damages so the foregoing limitations or exclusions may not apply This warranty gives the claimant specific legal rights The provisions of this warranty are in addition to and not a modification of or a subtraction from the statutory warranties and other rights and remedies contained in applicable local legislation To validate warranty return this registration form...

Отзывы: