manualshive.com logo in svg

Feeney DesignRail LED 40W-DK, Руководство по установке, Страница: 3 / 11

Поделиться
Скачать
Feeney DesignRail LED 40W-DK Скачать руководство пользователя страница 3

1-800-888-2418 | www.feeneyinc.com

3

POST ACCENT LIGHT - WIRING DIAGRAM

3

1

2

4

5

6

7

5

6

1. 

Power (by customer)

2. 

Light Switch (by customer) 

1

3. 

24v Dimmable Driver 

2

4. 

LED Starter Cable (20')

5. 

LED 2-Way Splitter

6. 

LED Post Accent Light

7. 

LED Extension Cable (132")

LIGHTING COMPONENTS:

1. Mount ver  cally only. See Switch Compatabilty 

Spec Sheet at www.feeneyinc.com

2.  See Driver Spec Sheet at www.feeneyinc.com

1
2
3
4
5

7

6

Determine loca  on of driver.  

Note: It is best to locate the drivers as close as 
possible to the ligh

ࢼ

 ng to reduce the possibility 

of voltage drop occuring.  If possible, the driver 
should be within 15 feet of the post that will 
accept the 20' starter cable.

Route exterior rated wiring from compa  ble 
dimmer switch/AC power source to loca  on of 
driver.
Connect drivers to dimmer switch/AC power 
source.
Connect 20' starter cable and route from driver 
to post using supplied wire nuts.

Step 1 - Install Drivers

Step 1A – Connect Source Power to Driver

IMPORTANT SAFETY NOTE: TO REDUCE RISK OF ELECTRICAL SHOCK, TURN OFF AC CIRCUIT BREAKER PRIOR TO COMMENCING ANY ELECTRICAL WORK AND 

CONNECTING DRIVER(S) TO AC POWER SOURCE.  VERIFY THAT LIVE POWER IS NOT PRESENT AT JUNCTION BOX WHEN MAKING CONNECTIONS.

Содержание DesignRail LED 40W-DK












Отзывы:

Нет отзывов