Federal Signal Corporation UltraVoice UVRI-B Series Скачать руководство пользователя

Страница: 15 / 56

Specifications

Description, Specifications, Installation, and Operation Manual

Federal Signal

www.fedsig.com

DTMF

String length

Mark/Space timing:

Decoder Minimum

Decoder Maximum

Encoder

Space between Stacked codes

All timings in milliseconds

3-12 standard DTMF characters

50 ms/50 ms (below 50/50 consult factory)

800 ms total mark/space timing per code

100 ms/100 ms mark/space timing

minimum 1.25 seconds

AFSK

Baud rate

Modem type

Mark frequency

Space frequency

Error checking

1200 bps

MSK (minimal shift key)

1200 Hz

1800 Hz

16 bit CRC

EAS

Supports standard EAS codes and wildcards

POCSAG

Supports Binary frequency shift keying

512 Baud numeric messages

Decode Sensitivity

18 dB SINAD for tone (except with CTCSS

tones > 200 Hz and decode tones < 400 Hz)

and 21 dB SINAD for MSK, EAS, POCSAG

and DTMF with 50 ms/50 ms or greater

timing

Two Way Formats

Federal Packet Digital and DTMF

Table 14 Environmental and Physical

Operating temperature range

-22°F to +150°F (-30°C to + 65°C)

Humidity

0-95%, non-condensing

Control cabinet (H x W x D)

20.36 x 16.30 x 6.62 inches

(51.7 x 41.4 x 16.8 cm)

UVRI-B (Weight without radio)

41.4 lb (18.8 kg)

Net Shipping Weight

45.4 lb (20.6 kg)

UVRI-BH and UVRI-BU (Weight with radio) 44.6 lb (20.2 kg)
Net Shipping Weight

48.6 lb (22.0 kg)

UVRI-B100 (Weight with amplifier)

44.8 lb (20.3 kg)

Net Shipping Weight

48.8 lb (22.1 kg)

UVRI-BH100 and UVRI-BU100

(Weight with radio and amplifier)

48.0 lb (21.8 kg)

Net Shipping Weight

52.0 lb (23.6 kg)

Содержание UltraVoice UVRI-B Series

























































Результаты поиска

Содержание UltraVoice UVRI-B Series

Отзывы:

Похожие инструкции для UltraVoice UVRI-B Series

Бренды по названию

Популярные бренды

Federal Signal Corporation UltraVoice UVRI-B Series, Описание, характеристики, установка и руководство по эксплуатации

Результаты поиска

Содержание UltraVoice UVRI-B Series

Отзывы:

Похожие инструкции для UltraVoice UVRI-B Series

Бренды по названию

Популярные бренды