Federal Signal Corporation UltraVoice UVRI-B Series Скачать руководство пользователя | Manualshive

Страница: 11 / 56

background image

11

General Description

Description, Specifications, Installation, and Operation Manual

Federal Signal

www.fedsig.com

•  Remote monitoring of system and speaker circuits
•  Optional cellular, satellite, or broadband IP communications
•  Stackable siren functions enable user pre-defined warning scenarios
•  600-ohm I/O for wire line control and status monitoring
•  600-ohm input/output for connection to external amplifiers and fire protection

systems

• Built-in 8 ohm (0.7 W) Audio Output. Typically used for cabinet speaker.
• Built-in 10 V/25 V (0.7 W) Audio Output. Typically used to interface 100 W optional

amplifier.

•  Monitoring and control of standard amplifier for voltage, current, and status
•  Two transceiver ports for radio communications
•  Built-in level meter to set and monitor receive level for radio interface
•  VOX to provide carrier detect for primary transceiver port
•  Optional noise monitoring for automatic level control
•  Real-time battery voltage monitoring
•  Ambient noise level monitoring with automatic volume control requires microphone

X-SM1-FS1

• Supervised and fault monitored TC1/TC2 Fire Alarm Panel Interface
• Local Audible and Visible Trouble Indicators

Ordering Information

All UVRI-B models are designed for two-way control and status monitoring using the

Federal Signal Commander System. You can equip all models with a microSD card for

local storage of voice and/or tone messages.

Table 1 Ordering Information

Model

Description

UVRI-B*

Remote Interface unit, IP enabled, battery backup

UVRI-BH*

Remote Interface unit, IP enabled, battery backup, VHF radio

UVRI-BU*

Remote Interface unit, IP enabled, battery backup, UHF radio

UVRI-B100*

Remote Interface unit, IP enabled, battery backup, 100 watt amplifier

UVRI-BH100*

Remote Interface unit, IP enabled, battery backup, VHF radio with

100 watt amplifier

UVRI-BU100*

Remote Interface unit, IP enabled, battery backup, UHF radio with

100 watt amplifier

*

Add the letter -V to the UVRI-B model name for a model with a volume knob for the

internal speaker.

«
...
9
10
11
12
13
...
»

Содержание UltraVoice UVRI-B Series

























































Отзывы:

Нет отзывов

Похожие инструкции для UltraVoice UVRI-B Series

Leroy-Somer R180

Бренд: Nidec Страницы: 20

Бренд: Samson Страницы: 48

Бренд: Mako Networks Страницы: 15

Бренд: Gantner Страницы: 56

Бренд: IDS Страницы: 2

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 111

Бренд: Kathrein Страницы: 16

Бренд: IBM Страницы: 38

REVOLUTION Pro Controller 2

Бренд: Nacon Страницы: 11

Бренд: Nacon Страницы: 18

Бренд: Nacon Страницы: 24

Бренд: Nabco Страницы: 35

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 31

Бренд: National Instruments Страницы: 50

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 21

Бренд: National Instruments Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды