Federal Signal Corporation SmartSiren Platinum SSP3000B Скачать руководство пользователя страница 59

Страница: 59 / 60

Getting Technical Support

Installation and Maintenance Instructions

Federal Signal www.fedsig.com

3. Place the new insulator on the terminal and insert the rear locking tab into the

housing.

4. Push the front of the insulator against the housing to lock the front tab.

Reinstalling the Siren Amplifier/Relay Module

To reinstall the siren amplifier/relay module in the vehicle (See Figure 40 on

page 58):
1. On the power terminals reinstall a flat washer followed by an external-tooth

lock washer.

2. Reconnect the power leads to the terminals and secure them with an external-

tooth lock washer and a Keps

nut.

3. Reconnect the Convergence Network cable, serial cables, and wiring.
4. Reinstall the siren amplifier/relay module in the vehicle with the installer-

supplied #10-32 mounting hardware.

Getting Technical Support

For technical support and service, please contact:
Service Department

Federal Signal Corporation

Phone: 1-800-433-9132

Email: [email protected]

www.fedsig.com

Getting Repair Service

The Federal Signal factory provides technical assistance with any problems that

cannot be handled locally.
Any units returned to Federal Signal for service, inspection, or repair must be

accompanied by a Return Material Authorization (RMA). Obtain a RMA from a local

Distributor or Manufacturer’s Representative.
Provide a brief explanation of the service requested, or the nature of the

malfunction.
Address all communications and shipments to the following:
Federal Signal Corporation

Service Department

2645 Federal Signal Drive

University Park, IL 60484-3167

Содержание SmartSiren Platinum SSP3000B




























































Результаты поиска

Содержание SmartSiren Platinum SSP3000B

Отзывы:

Похожие инструкции для SmartSiren Platinum SSP3000B

Бренды по названию

Популярные бренды

Federal Signal Corporation SmartSiren Platinum SSP3000B, Инструкция по установке и обслуживанию

Результаты поиска

Содержание SmartSiren Platinum SSP3000B

Отзывы:

Похожие инструкции для SmartSiren Platinum SSP3000B

Бренды по названию

Популярные бренды